Contact Us

UCC256404BDDBR

Brand: Texas Instruments
Texas Instruments UCC256404BDDBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC256404BDDBR — Power Management & Signal Chain | Superb Automation

UCC256404BDDBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC256404BDDBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC256404BDDBR: LLC resonant controller with burst mode and a 700 V high side driver

UCC256404BDDBR is a secondary side controller for an LLC half bridge that drives the high and low side FETs and holds the resonant tank in zero voltage switching in a SOIC (DDB) body of 14 pins. The high voltage pin is rated 700 V and the driver is integrated, with 0.6 A of source and 1.2 A of sink current, so the half bridge needs no external driver and no bootstrap diode. Control is hybrid hysteretic rather than linear, which is what gives the fast transient response and the quick exit from burst mode.

Order code and package

Order code read outUCC256404B DDB R: device UCC256404 revision B, DDB fourteen pin SOIC, R large tape and reel
PackageSOIC (DDB), 14 pins
Carrier in the vendor addendumUCC256404BDDBR at 2500 pieces on a large reel, and a 250 piece small reel row is also published
Moisture levelLevel 2, 260 degrees, one year floor life
Lead finishNickel palladium gold
Operating temperatureminus 40 to plus 125 degrees, quoted per orderable row
B revision markerthe B suffix is on the part number, not a date code, and it changes the high side floating supply rating

Electrical parameters that decide the application

High voltage pin ratingHV and HB are rated 700 V absolute maximum, enough for a 400 V DC bus with margin for ringing
Floating supply ratingHB to HS is rated 25 V on the B version, against 17 V on the earlier members, which is the reason the B part exists
High side driver0.6 A source and 1.2 A sink, integrated, with adaptive dead time
VCC start26 V typical to start from the internal JFET, then the regulated rail takes over at 13 V
VCC undervoltage7.85 to 8.70 V rising with 0.25 V of hysteresis, and the JFET re-enables below 9.65 V
Regulated supplyRVCC at 13 V, 12.7 to 13.45 V unloaded, holding 12.4 V minimum at a 100 mA load
Burst sleep current780 uA typical from VCC while the burst off period runs, which is the standby budget
Run current2.2 mA typical while switching, excluding gate charge
Rejection and timingAdaptive dead time, capacitive region avoidance, and a soft start that ramps the reference
ProtectionsOver temperature, output overvoltage, input undervoltage and three levels of overcurrent
X capacitor dischargeAn active discharge path is integrated, which removes the bleed resistors across the input capacitor
Control methodHybrid hysteretic control, which behaves like a charge pump on the tank rather than a linear error amplifier

Family members and how they differ

UCC256404Bthe part on this page, latched fault behaviour and the 25 V floating supply rating
UCC256402 and UCC256403same control core, different start up and fault handling rows in the comparison table
A suffixthe A variants are listed beside the base parts and differ in protection latching rather than in the driver
UCC28056the transition mode PFC controller the vendor pairs with this part for a two stage supply
UCC24624the dual synchronous rectifier controller that completes the secondary side, quoted as reaching 80 mW of system standby

Points to check before this part goes on a BOM

The B suffix is an electrical difference, not a revision label. The floating supply between HB and HS is rated 25 V on this part against 17 V on the earlier members, which matters when the gate drive is run from a 12 V rail and the switch node rings. A board that was written around the 17 V limit and then moved to the B part gains margin, while the reverse move loses it, so the suffix belongs in the bill of materials rather than in a note.

Burst mode is the feature that decides standby power, and its behaviour is programmable. The burst power level and the hysteresis are set by external components, and the soft on and soft off periods are what stop the tank from producing audible noise at no load. The same pin configuration can disable burst entirely, which is the right choice for an application that never sits at no load and needs the lowest output ripple instead.

Hybrid hysteretic control is not a small signal loop. It charges and discharges the resonant capacitor in steps, so the response to a load step is a number of cycles rather than a settling curve. That is what produces the fast exit from burst and the tight transient response, and it also means the conventional error amplifier compensation arithmetic does not apply. Engineers who try to tune it like a voltage mode loop usually end up fighting the capacitive region avoidance instead.

Three levels of overcurrent protection exist for a reason. A hard short at the output, an overload that the tank can still support, and a gradual current rise each take a different path, and the controller reacts differently to each. The result is that a shorted secondary is handled without a continuous high current in the primary, which is what keeps the FETs inside their safe operating area during a fault test.

The integrated JFET start up removes the usual trickle resistor chain from the AC side. VCC is charged from the high voltage pin until the regulated rail takes over at 13 V, and the JFET is then disabled, which is why the standby current can be quoted at 780 uA during burst off. That also means the start up behaviour depends on the bus capacitance: a very large hold up capacitor slows the first start because the JFET charges VCC from a bus that is itself still rising.

Where this order code fits

Used in AC to DC supplies from roughly 75 W to 300 W where standby power and audible noise both matter: laptop and monitor adapters, TV power boards, LED drivers, server auxiliary supplies and industrial DIN rail power supplies that must meet DoE Level VI and EU CoC Tier 2. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

What is the difference between the B part and the plain UCC256404? The floating supply rating between HB and HS. The B part is rated 25 V, the other members 17 V. Control behaviour, pin out and package are the same, so the choice comes down to gate drive level and switch node ringing.

Can burst mode be turned off? Yes, through the pin configuration. With burst disabled the supply runs continuously at light load, which costs standby power but removes the low frequency output ripple that burst produces.

Does it need an external high side driver? No. The high side driver is integrated with 0.6 A source and 1.2 A sink, which is sized for the FETs used in a few hundred watt LLC stage. A much larger FET needs an external buffer.

What pairs with it on the primary side? The vendor names the UCC28056 or UCC28064A PFC controllers, and the UCC24624 as the secondary synchronous rectifier controller. That combination is the reference for the sub 80 mW standby claim.

Is the 700 V rating enough for a 400 V bus? Yes, with the usual derating. The pin sees the bus plus the resonant overshoot, so a 400 V nominal bus that can reach 420 V at high line still leaves margin. A 380 V bus with heavy ringing should be measured rather than assumed.

What dead time should be programmed? The controller adapts the dead time to the tank current, so the external setting is a starting window rather than a fixed number. A bench sweep of the half bridge waveform at low line and light load shows whether the body diode is conducting before the FET turns on, and that is the condition that wastes efficiency.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.