TPSM861253RDXR
Product Specifications
TPSM861253RDXR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPSM861253RDXR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPSM861253RDXR: the fixed 3.3 V member of the family buys accuracy with a divider that never drifts
The TPSM861253RDXR is the same 1 A, 3 V to 17 V module as its two siblings with one difference that matters at the bench: the feedback divider and its feedforward capacitor are inside the package and the output is fixed at 3.3 V. The published window is 3.27 V to 3.33 V at 25 C and 3.25 V to 3.35 V across the full range, which is plus or minus 1 percent from 0 C to 65 C. For a product team that would otherwise spend two resistors and a placement on every board, and then watch the divider tolerance eat the margin on a 3.3 V logic rail, that is a real saving.
The 253 runs forced continuous conduction, so the switching waveform stays at 1.4 MHz at every load and the output ripple does not change shape when the load falls below 100 mA. That is the version to take when a downstream ADC or a radio reference cannot tolerate the low frequency ripple that a pulse skipping converter produces at light load, and when the extra 270 microamps of no load current against the Eco-mode member is not the limiting number in the standby budget.
Key electrical data for the TPSM861253RDXR
| Input range | 3 V to 17 V, UVLO wake 2.9 V typical, shutdown 2.7 V, hysteresis 200 mV |
| Output | 3.3 V fixed, 3.27 V to 3.33 V at 25 C, 3.25 V to 3.35 V over -40 C to 125 C |
| Current | 1 A continuous, valley current limit 1.5 A to 3.1 A across the set point spread |
| Switches | 55 milliohm high side at 5 V in and 24 milliohm low side, both at 25 C |
| Switching | 1.4 MHz nominal, 95 percent maximum duty, minimum on time 60 ns |
| Quiescent | 370 microamps no load with the switches running, 2 microamps in shutdown |
Package, marking and reel data
| Body | RDX, 7 pin QFN-FCMOD, 3.30 mm by 4.00 mm by 2.00 mm |
| Reel | 3000 pieces on a 330 mm reel, 12.4 mm carrier, pocket 3.6 by 4.3 by 2.3 mm |
| Finish | NIPDAU, level 2 at 260 C, one year floor life |
| Marking and grade | 861253 on the top, -40 C to 125 C junction |
What a fixed output means for the board
The feedback pin is not brought out on this member, so the output cannot be trimmed and cannot be raised above 3.3 V. On a board where the same rail also feeds a 3.6 V minimum load, this part is the wrong choice and the 252 with an external divider is the right one. On a board where the rail is 3.3 V logic and the tolerance analysis has already accounted for plus or minus 1 percent, the fixed part removes two placement positions and the divider drift that comes with a 100 ppm resistor pair over temperature.
Because the switching frequency is fixed, the input filter can be tuned once. The module draws a 1.4 MHz square wave current from the input, and a 10 microfarad ceramic plus a 100 nanofarad at the pin keeps the conducted emission below the limits that a CISPR 11 class B scan looks for. The output capacitor should be 22 microfarad to 47 microfarad of ceramic for a 1 A step, and the effective capacitance after DC bias is the number to use, not the nominal label. Our pin to pin cross reference page covers the module family and the codes that share this footprint.
Buyer questions on the TPSM861253RDXR
Can the two modules be mixed on one board? They share the RDX body and the pinout, so the same land pattern takes the 252, the 253 and the 257. The difference is the feedback pin and the light load behaviour, so a board that populates either code needs both dividers placed or the fixed part left to run open loop on its internal divider.
Does the module need a minimum load? No. The forced continuous member runs at constant frequency from no load upward, and the Eco-mode member simply skips pulses. Neither needs a bleeder resistor to stay in regulation.
Is the 3.3 V output good enough for a radio reference? It is good to 1 percent, which is fine for digital and for most transceiver supplies, but a synthesizer that needs better than 1 percent should use a linear regulator after this module rather than the module alone.
Availability and cross reference
This code ships 3000 pieces per reel and the reel label carries the moisture level, which is level 2 at 260 C on the published row. A customer who has been buying the adjustable member and wants to remove the divider has to check the land pattern once, because the feedback pin on the fixed part is still present on the package and must be left unconnected rather than tied to the output. We stock both codes against forecast and kit them together when a build uses the same rail in two variants, and the handling note for each lot is recorded in our incoming inspection plan.