Contact Us

TPSM63610RDFR

Brand: Texas Instruments
Texas Instruments TPSM63610RDFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM63610RDFR — Power Management & Signal Chain | Superb Automation

TPSM63610RDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM63610RDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM63610RDFR: an 8 A step down power module that carries its own inductor and passives in a 7.5 mm by 6.5 mm package

TPSM63610RDFR is a synchronous buck power module with the MOSFETs, a shielded inductor and the passives inside one overmolded package, so the board only has to add input and output capacitors and a feedback divider in a B3QFN (RDF) body of 22 pins. It accepts 3 V to 36 V at the input, delivers 1 V to 20 V at up to 8 A with a 10 A peak, switches from 200 kHz to 2.2 MHz, and reaches 95 per cent efficiency at the top of its load range. Shutdown current is 0.6 microamp typical.

Order code and package

TPSM63610RDFRB3QFN (RDF) body, 22 pins, 7.50 mm by 6.50 mm and 4 mm tall, 1000 pieces on a large reel, nickel palladium gold finish, moisture level 3 at 250 C for 168 hours, marking 63610, minus 40 C to 125 C
TPSM63610RDFRG4the same module with the G4 suffix, same body and same packing, the row to order when the finish has to be stated explicitly
Suffix rowsthe addendum repeats both strings with an .A suffix, and the packing and moisture level have to be read on the row
Pin compatibilitythe body is pin compatible with the TPSM63608, a 36 V 6 A module, so a board can move between the two current ratings without a new land pattern
Thermal padsfour large pads sit under the module and are the only path for the heat the integrated switches and inductor produce
Height4 mm overmolded, which is the number that decides whether the module fits under a shield can or a connector

Electrical parameters that decide the application

Input voltage3 V to 36 V operating, which covers a 12 V and a 24 V industrial bus with margin for transients
Output voltage1 V to 20 V set by a divider, so the same module covers a core rail and a 15 V analog rail
Output current8 A continuous with a 10 A peak, and the inductor inside the package is rated for that current rather than for a lower one
Switching frequency200 kHz to 2.2 MHz set by a resistor on the RT pin, or locked to an external clock in the same range
Low side current limit8 A minimum, 9.2 A typical and 10.5 A maximum on the 8 A variant, which is where the peak rating comes from
Negative current limitminus 3.9 A to minus 6.4 A, which matters when the module is used as an inverting buck boost and the inductor current reverses
Internal VCCunder voltage lockout at 3.75 V with 1.2 V of hysteresis, which keeps the module off until the input is really up
Quiescent current0.6 microamp typical in shutdown, which is what makes the module usable on a standby rail
Thermal resistance18.2 C per watt junction to ambient on the evaluation board, and 22 C per watt on a JESD 51-7 board
Efficiency95 per cent peak across the load range, with an external bias option that improves the number at light load
EMIthe package uses dual input paths and integrated input capacitors, meets CISPR 11 and 32 Class B, and offers a resistor adjustable switch node slew rate
Modesforced PWM for constant frequency across the load range, or PFM for higher light load efficiency

Family variants and how they differ

TPSM63608the 36 V 6 A member on the same pinout, which is the drop in choice when the load turns out smaller than the first estimate
TPSM63610the 8 A member, same body, same pinout, same external components apart from the feedback divider
Inverting usethe module supports a negative output when the output is referenced to the switch node instead of ground, which is how a minus 12 V rail is built from a 12 V bus
Bias pinan external bias from the output improves efficiency at light load, at the cost of one more connection
Slew rate pina resistor sets the switch node slew, which trades a little efficiency for a quieter spectrum

Points to check before this part goes on a BOM

The module removes the inductor from the BOM but not the capacitors. Four external components are enough for a working rail, and the input capacitor still has to be placed at the corner pins where the package puts VIN.

The current limit is the low side switch limit, not a load current limit. The 8 A, 9.2 A and 10.5 A figures describe the switch, and the load current that trips it depends on the ripple and the duty cycle.

Negative current is allowed. In an inverting arrangement the inductor current reverses, and the negative limit of minus 3.9 A to minus 6.4 A is what keeps the module from running away when the load disappears.

The thermal number is board dependent. 18.2 C per watt is measured on the evaluation board with its copper, and a board with less copper under the pads will run hotter at the same load.

Pin compatibility is the reason to pick this family. A 6 A or an 8 A requirement can be met from one land pattern, which avoids a board respin when the load estimate moves.

Where a module beats a discrete converter

A discrete 36 V converter needs an inductor, a compensation network and a careful switch node copper area before it can pass an emissions test. The module moves all three inside the package, so the only radio frequency problem left on the board is the input loop.

The trade is cost per amp and the fixed height. When the rail is under 5 A and the board has room, a discrete converter is cheaper. When the rail is 8 A, the board is dense and the schedule is short, the module usually wins on total cost once the inductor and the test time are counted.

The fourth decision is the input capacitor. The module is rated for its ripple current with a defined input capacitor close to the VIN and GND pads, and a board that moves that capacitor away adds inductance to the input loop, which shows up as a higher conducted emission at the switching frequency and a larger voltage dip during a load step. The package puts VIN and VOUT at the corners for exactly that reason, and the capacitors follow the corners rather than the middle of the body.

Where this order code fits

It fits a 12 V or 24 V industrial bus that has to produce a 5 A to 8 A rail in a dense area, which is the shape of a test instrument, a factory controller or a telecom line card. Teams comparing it with a neighbouring part start from our Component Lead Time Solutions page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

Does the module need an external inductor? No. The inductor, the MOSFETs and the passives are inside the package, and a working rail needs as few as four external components, mostly capacitors and the feedback divider.

Can it produce a negative rail? Yes. The module supports a negative output voltage, and the negative current limit of minus 3.9 A to minus 6.4 A is specified for that use.

What decides the switching frequency? A resistor on the RT pin sets it between 200 kHz and 2.2 MHz, and the same pin accepts an external clock when the rail has to be synchronised to a system clock.

Is the 8 A rating continuous? Yes, 8 A continuous with a 10 A peak, and the inductor inside the package is rated for that current rather than for a lower figure.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.