Contact Us

TPSM53603RDAR

Brand: Texas Instruments
Texas Instruments TPSM53603RDAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM53603RDAR — Power Management & Signal Chain | Superb Automation

TPSM53603RDAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM53603RDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM53603RDAR: 36 V input 3 A step down power module in a 5 by 5.5 mm QFN

TPSM53603RDAR is a complete synchronous buck stage with the MOSFETs, inductor, controller and passives inside one overmoulded package in a B3QFN (RDA) body of 15 pins. Because the magnetics and the compensation are inside the module, the external part count drops to four components, and the switching frequency is fixed at 1.4 MHz. It delivers 3 A from an input between 3.8 V and 36 V and sets the output anywhere from 1 V to 7 V with two resistors.

Order code and package

Order code read outTPSM53603 RDA R: module TPSM53603, RDA fifteen pin B3QFN, R large tape and reel
PackageB3QFN (RDA), 15 pins, 5.0 mm by 5.5 mm by 4.0 mm, single thermal pad, all pins on the perimeter
Carrier in the vendor addendumTPSM53603RDAR at 1000 pieces on a large reel, and the RDARG4 row is the same reel with the green material code
Moisture levelLevel 3, 245 degrees peak reflow, 168 hour floor life
Lead finishNickel palladium gold
Thermal windowjunction minus 40 to plus 125 degrees, ambient minus 40 to plus 105 degrees
Absolute maximum38 V on the input, 5.5 V on the feedback pin, 22 V on the power good pin, 245 degrees peak reflow case

Electrical parameters that decide the application

Input voltage range3.8 V to 36 V, with turn on at 3.55 V typical and turn off at 3.05 V, so a 24 V industrial rail and a 5 V rail both fit
Output voltage range1 V to 7 V set by a divider against a 1 V reference
Output current3 A, with up to 18 W delivered at 85 degrees ambient without airflow
Feedback accuracy0.985 V to 1.015 V over the full junction range, which is plus or minus 1.5 percent
Internal bias rail5 V LDO at the V5V pin, 4.75 to 5.25 V, which is also the pull up reference for power good
Switching frequency1.4 MHz fixed internally, which keeps the inductor inside the package small and the output ripple easy to filter
Overcurrent threshold4.5 A typical, so the module tolerates a short overload before it trips
Hiccup behaviourThe feedback pin below 0.4 V starts a hiccup wait of 94 ms, then the module retries into soft start
Soft start4 ms internal ramp, no external capacitor required
Enable thresholds1.23 V rising with 100 mV of hysteresis, and a second lower threshold at 1.0 V that gates the internal LDO
Quiescent current24 uA typical while regulating without switching, and 5 to 10 uA when shut down
EmissionThe vendor states compliance with CISPR 11 radiated limits with the recommended input filter

Family variants and how they differ

TPSM536033 A, the member on this page, 3.8 V to 36 V in, 1 V to 7 V out
TPSM536044 A in the same footprint and pin out, for a board that may need more headroom later
TPSM536022 A in the same footprint, for a lower current rail that can share the same land pattern
RDARG4 rowidentical reel and package with the G4 green material suffix, which matters to a customer tracking material declarations
Shock and vibrationthe module family is tested to Mil STD 883D, which is the reason it appears in ruggedised assemblies

Points to check before this part goes on a BOM

The 3 A rating is a thermal statement as much as an electrical one. The vendor quotes 18 W of output at 85 degrees ambient with no airflow, which at a 5 V output is 3.6 A and at a 3.3 V output is 5.4 A, both above the 3 A limit, so the electrical limit binds first in a cool enclosure and the thermal limit binds in a sealed box at high ambient. A quote for a sealed enclosure should be checked against the derating curves rather than the headline current.

The fixed 1.4 MHz frequency is the trade the module makes. It keeps the internal inductor small and the loop compensation inside the package, at the cost of higher switching loss than a 400 kHz discrete stage. For a 24 V to 5 V rail at 3 A the loss is acceptable, but the same module at 36 V to 1 V and 3 A runs a duty near three percent and spends most of the cycle in the high side switch transition, which is where efficiency drops away from the 95 percent peak.

A 4.5 A overcurrent threshold on a 3 A part leaves 50 percent of margin, which is deliberate, because the module has to survive the inrush into a large output capacitor at start up. When the feedback pin falls below 0.4 V the module stops, waits 94 ms and retries, so a hard short produces a low duty hiccup rather than a continuous 4.5 A into the fault. The 94 ms wait is long enough to be visible on a current probe and is the signature to look for when a board restarts under load.

Two enable thresholds exist in series. The first, at about 1.0 V, starts the internal LDO and gives the module a bias rail, and the second, at 1.23 V, starts switching. That two step arrangement is what allows a precise input undervoltage lockout to be built from the same pin with a divider, and it also means a slow rising supply passes through a region where the module is biased but not switching, drawing the 24 uA quiescent current.

The pins are all on the perimeter with one large thermal pad, which is what makes the part usable in a normal reflow process without X-ray. The pad carries the heat into the board, so the copper under it is the real thermal specification. A module dropped onto a two layer board with a thin pad connection will run far hotter than the data sheet curves, and that shows up as a current foldback at high ambient rather than as a dead part.

Where this order code fits

Suited to industrial, instrumentation and telecom boards that take a wide input, from a 12 V or 24 V bus down to 5 V, 3.3 V or 1.8 V rails, particularly where the enclosure has no airflow and the board area for a discrete buck stage is tight. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can the 4 A version drop into the same land pattern? Yes. The vendor states pin compatibility across the 2 A, 3 A and 4 A members, so a board can be laid out once and populated by current need. The 4 A part still needs the same external components, and its overcurrent threshold is higher, which changes the fault behaviour.

What output capacitor is needed? The data sheet electrical table is written against three 22 uF, 25 V, 1210 ceramic capacitors on the output and two 10 uF, 50 V, 1206 parts plus a 100 nF on the input. Those values are the reference condition, and dropping to a single output capacitor changes both the ripple and the loop.

Is a heat sink required at 3 A? Not at moderate ambient, because the module is specified for 18 W at 85 degrees with no airflow, but the pad has to be soldered to enough copper. In a sealed enclosure above 85 degrees the current has to come down, and the derating curves in the data sheet are the place to read that.

How does it handle a pre-biased output? It starts into a pre-biased output without discharging it, which matters when a rail is held up by another source during a restart. That behaviour is listed as a feature and needs no extra component.

Which packing does production receive? The published rows are 1000 piece large reels. A G4 suffix row exists with the same reel and package for customers who need the green material declaration, and that suffix should be named on the purchase order.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.