TPS92200D1DDCR
Product Specifications
TPS92200D1DDCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS92200D1DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS92200D1DDCR: 4 V to 30 V input, 1.5 A synchronous buck LED driver, PWM and analogue dimming, SOT-23-6
TPS92200D1DDCR is a synchronous buck LED driver rated 1.5 A with a 30 V input ceiling and two dimming methods on one control pin in a SOT-23 body of 6 pins. The driver regulates the current in an LED string rather than a voltage, with a feedback threshold of 99 millivolt, so the sense resistor dissipates almost nothing. The peak current mode loop is compensated internally, and the 1 MHz switching frequency keeps the inductor and the capacitor small enough for a camera body.
Order code and package
| TPS92200D1DDCR | Active, SOT-23-6 thin, 3000 pieces on a large reel, SN finish, MSL-2-260C with a one year floor life, marking 1SZK |
| TPS92200D2DDCR | Active, the analogue only dimming member, same body and reel |
| TPS92200D1RXLR | Active, the VQFN-HR body at 1.5 mm by 2.0 mm, for boards that need the smaller footprint |
| Switch resistance | 150 milliohm high side, 90 milliohm low side, both integrated |
| Temperature range | minus 40 to 85 degrees on the published rows |
Electrical parameters that decide the application
| Input voltage | 4 V to 30 V |
| Output current | 1.5 A continuous in the LED string |
| Feedback voltage | 99 mV plus or minus 3 mV, so the sense resistor is small |
| Switching frequency | 1 MHz fixed |
| Maximum duty cycle | up to 99 per cent, so the string can sit close to the input voltage |
| Shutdown current | 1 microamp |
| Dimming | PWM dimming through a digital input and analogue dimming through an analogue input on the D1 member |
| Protection | LED open, LED short, output short to ground, sense resistor open, thermal shutdown, all with auto retry |
Family variants and how they differ
| TPS92200D1 | PWM and analogue dimming, the string on this page |
| TPS92200D2 | analogue dimming only, with the reference set by the duty cycle of a PWM input |
| FB threshold | 99 mV, so a 1.5 A string needs a 66 milliohm sense resistor |
| Body | SOT-23-6 thin at 1.6 mm by 2.9 mm, or the VQFN-HR for a smaller area |
| Compensation | internal to the peak current mode loop, no external network |
Points to check before this part goes on a BOM
Ninety nine millivolt of feedback is the reason the sense resistor is small. At 1.5 A a 66 milliohm resistor drops 99 mV and dissipates 0.15 W. A driver with a 200 mV threshold would dissipate twice that in the same string, which in a camera body is the difference between a warm housing and a hot one. The three millivolt tolerance on a 99 mV threshold is three per cent of the current setting.
The two dimming members are not interchangeable in firmware. On the D1 member an analogue voltage on the control pin scales the reference between 5 and 100 per cent. On the D2 member the duty cycle of a PWM signal scales the reference between 1 and 100 per cent. A board built for one and fitted with the other will light the string at the wrong current, and the fault looks like a software problem.
The string voltage has to sit below the input voltage. This is a buck driver, not a buck boost. A 24 V input can drive a string of up to about 23 V, and a string that needs more will not regulate. At 99 per cent maximum duty cycle the headroom is small but real, and the switch resistance and the inductor resistance eat into it.
The 1 microamp shutdown current is what a camera needs. A surveillance camera that runs its illuminator for a few seconds at a time cannot afford a driver that draws milliamp in the off state, because the off state is almost all of the time. That figure is the reason the part appears in that application rather than a general purpose converter with a current sense.
Auto retry protection is a choice with a consequence. An LED open or a short to ground shuts the driver down and it retries continuously. That keeps the part alive and produces a visible flicker in a lighting product. Where a flicker is not acceptable the fault has to be detected by the system, and the driver alone will not report it.
Peak current mode with internal compensation limits the inductor choice. The loop is closed for a range of inductor values and output capacitors. A much larger inductor, fitted to reduce ripple current, will move the loop and can produce an oscillation that shows as a slow current envelope on the string.
Eighty five degrees ambient is the ceiling on the SOT body. A driver running 1.5 A from 24 V into a 20 V string dissipates in the switches and the inductor, and inside a camera housing at 70 degrees there is very little margin. The VQFN body has a better thermal path and the same silicon, which is the version to use when the enclosure is tight.
The sense resistor is part of the current accuracy. The three millivolt feedback tolerance is only half of it; the resistor tolerance and its temperature coefficient are the other half. A 1 per cent resistor with a 100 ppm drift over a 60 degree rise adds more error than the driver does, so the resistor choice is not a detail.
MSL-2 with one year floor life applies to both bodies. A 1.5 A driver is usually placed on a board that goes through a full reflow, and a reel that has been open for months carries a real delamination risk. For a repair order, the seal date on the bag is as important as the part number.
What to confirm before this part goes on a purchase order
Confirm the string voltage and the current, and confirm which dimming method the firmware uses. The D1 and D2 members look the same on a reel and behave differently on the control pin.
Ask for the date code and the packing. The SOT-23 body is published on a 3000 piece large reel, so a small repair quantity means a broken reel, and the moisture sensitivity means the seal date matters.
The string current and the number of LEDs in series decide the sense resistor and the inductor, and neither can be checked from the part number. State both on the enquiry so the offer can be matched to the board rather than to the family. The number of LEDs and the string current are the two fields that decide whether the part is suitable at all, so they belong in the first message.
Where this order code fits
It drives a white or infrared LED string from a 12 V or 24 V rail in a surveillance camera or a machine vision lamp, with dimming from a PWM or an analogue signal. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can it drive a string that needs more voltage than the input? No. It is a buck driver, so the string voltage has to be below the input voltage minus the resistive losses. A string that needs more needs a boost or a buck boost driver.
What value sense resistor does it need? The feedback threshold is 99 mV, so the resistor is 99 mV divided by the string current. At 1.5 A that is 66 milliohm, and the resistor still has to be rated for the 0.15 W it dissipates.
Does it need an external compensation network? No. The peak current mode loop is compensated inside the package. The inductor and the output capacitor still have to be inside the characterised range for the loop to stay stable.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.