Contact Us

TPS84210RKGR

Brand: Texas Instruments
Texas Instruments TPS84210RKGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS84210RKGR — Power Management & Signal Chain | Superb Automation

TPS84210RKGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS84210RKGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS84210RKGR: a 2 A step down module that needs three external parts

The TPS84210RKGR is a complete 2 A synchronous buck supply in a 39 pin B1QFN package, with the MOSFETs, the inductor and the compensation inside. It takes 2.95 V to 6 V at the input and produces 0.8 V to 3.6 V set by a single resistor, with 1 percent reference accuracy and efficiency up to 96 percent. The data sheet says the solution needs as few as three external components, which is the reason a board team picks a module over a controller and a discrete inductor.

The control set is what a point of load supply needs. A resistor from VADJ to ground sets the output, an optional resistor on RT/CLK sets the switching frequency between 650 kHz and 1.5 MHz or synchronises to an external clock, the SS/TR pin ramps the output or tracks another rail, and the PWRGD pin reports the rail state. INH/UVLO gives a precision enable with its own threshold. All of that sits behind a package that mounts with standard QFN techniques.

Key electrical data for the 2 A module

Input range2.95 V to 6 V, with an undervoltage lockout at 2.75 V falling
Output range0.8 V to 3.6 V, set by one resistor from 0.8 V open to 459 Ohm at 3.3 V
Output current2 A continuous, with the inductor rated inside the package
Efficiencyup to 96 percent at 3.3 V out, 5 V in, 1.5 MHz
Switching frequency650 kHz to 1.5 MHz by resistor, or synchronised to an external clock
Accuracy1 percent reference, with set point, line, load and temperature in the total window
ControlPWRGD, SS/TR tracking, INH/UVLO enable, and a frequency resistor pin

Package, marking and reel data

BodyB1QFN RKG, 39 pins, low profile, thermal pad for the ground and heat path
Reel500 pieces with the R suffix, 250 with the T suffix
Finish and moistureNIPDAU, level 3, 250 C peak reflow, 168 hour floor life
Temperaturejunction range minus 40 to 85 C on this row, which is narrower than the automotive parts
MarkingTPS84210 on the package top

Where an integrated 2 A buck earns its area

DSP and FPGA point of load rails, test equipment, industrial controllers and communications line cards are the applications named in the data sheet. The case for the module is the loop: a 2 A converter at 1.5 MHz needs a compensation network that has been checked against the output capacitor, and the module arrives with that check done. The board team spends its time on the load rather than on the supply.

The 85 C junction limit is the constraint to read carefully. It is lower than the 125 C or 150 C of the automotive regulators in this batch, so the module suits a cabinet or a benchtop product better than an engine bay. At 2 A and 90 percent efficiency the package dissipates about 700 mW, and the thermal pad is what carries it into the ground plane. The 500 piece reel is also a statement about the intended volume: this is a part for a product built in thousands, not in millions, and a customer whose annual use is a few hundred boards should plan the buy around that reel rather than around weekly replenishment. A 500 piece reel is also the natural lot size for a traceable build, where every board carries the date code of one reel and a field return can be traced to a lot instead of to a quarter of production.

Buyer questions on the TPS84210RKGR

What sets the output voltage? One resistor between VADJ and ground. The data sheet prints the value for each common rail: open for 0.8 V, 2.87 kOhm for 1.2 V, 1.15 kOhm for 1.8 V, 673 Ohm for 2.5 V and 459 Ohm for 3.3 V.

Can the switching frequency be moved out of a band? Yes, the RT/CLK resistor sets it from 650 kHz to 1.5 MHz, and the pin also accepts an external clock so several modules can run in step. That is how a multi rail board keeps its emissions inside one band.

What does the R suffix mean on the reel? Packing. The R suffix is 500 pieces, the T suffix is 250, and the part is the same. A prototype build usually takes the T and a production build the R.

Buying this module through a component supplier

A 39 pin module with an inductor inside is a long lead item when the market is tight, and it is not substitutable without a board change. Our component shortage forecast page covers the early warning route, and power management cross reference lists the pin compatible alternatives when a plan needs one.