TPS82130SILR
Product Specifications
TPS82130SILR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS82130SILR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS82130SILR: 17 V input 3 A step down module with tracking
TPS82130SILR is a 3 A step down module that takes a 3 V to 17 V input and includes the inductor and the tracking input in a MicroSiP (SIL) body of 8 pins. The output is adjustable from 0.9 V to 6 V, the module switches at 2 MHz, draws 20 microamps in power save mode, and brings a soft start and tracking pin so the rail can follow another supply during power up.
Order code and package
| Order code read out | TPS82130 SIL R: family, SIL 8 pin MicroSiP, R tape and reel |
| Package | MicroSiP, 8 pins, 3.00 mm by 2.80 mm, 1.50 mm tall, inductor inside |
| Operating temperature | minus 40 to plus 125 degrees Celsius |
| Switching frequency | 2 MHz nominal |
| Pinout | EN, SS/TR, FB, PG and the power pins, the same eight pins as the rest of the family |
| Local language document | a Mandarin edition of the data sheet is published alongside the English one |
| Calculation support | the vendor power tool covers this module for a first pass calculation |
Electrical parameters that decide the application
| Input voltage | 3 V to 17 V, which covers a 12 V rail directly and a 15 V rail with margin |
| Output voltage | 0.9 V to 6 V adjustable |
| Output current | 3 A continuous |
| Quiescent current | 20 microamps in power save mode |
| Topology | DCS-Control, which keeps the transient response fast without an external compensation network |
| Soft start and tracking | a capacitor on SS/TR sets the ramp, and a voltage on the same pin makes the output follow it |
| Duty cycle | 100 percent for the lowest dropout, useful when the input sags |
| Protection | thermal shutdown and current limit, both internal |
| Feedback | an external divider sets the output between 0.9 V and 6 V |
| Output capacitor | ceramic, with the value driven by the load transient rather than a minimum ESR rule |
Family variants and how they differ
| TPS82130 | 3 A, 17 V input, the part on this page |
| Lower voltage members | the family also covers 6 V input parts for 5 V rails, with the same eight pin outline |
| Tracking | SS/TR is the sequencing feature, and it is what separates this part from a plain regulator module |
| Higher current | 3 A is the top of this body, above that the family moves to a larger package |
| Module benefit | the inductor and the switch node are inside, so the emission loop is small by construction |
Points to check before this part goes on a BOM
Tracking is the feature that solves a sequencing argument. The SS/TR pin accepts a voltage ramp and the output follows it, so a 1.2 V core rail can be tied to a 1.8 V rail and rise proportionally. That avoids the classic failure where a core rail arrives before its input and output stage, and it does so without an external supervisor.
The 3 A rating depends on the input and output combination. At 12 V in and 1.8 V out the module dissipates about 0.8 W at 3 A, which the 3.0 mm by 2.8 mm body can pass with a copper pad. At 17 V in and 0.9 V out the same current is over 1.5 W and the junction limit arrives earlier. Ambient temperature is the third variable, and a sealed enclosure derates the part well below 3 A.
The output floor is 0.9 V. A 0.8 V core rail, which appears on older processors, is outside the range, so the part cannot be used for it. The adjustable divider also has a minimum ratio, so the practical lowest output is the reference voltage, not zero.
100 percent duty cycle is a dropout feature, not a regulation feature. When the input falls toward the output, the high side switch stays on and the output follows the input minus the resistive drop. That keeps a 5 V rail alive through a 5.5 V brownout, and it also means the output is no longer regulated, so any downstream circuit that needs 5 V plus or minus 5 percent has to be checked against the sag.
The module is a system in package, so the reflow profile matters. The inductor and the die sit in one body with a stated moisture level, and a profile borrowed from a plain QFN can leave voids under the power pads. The vendor's recommended profile is not optional, and second source modules rarely share it.
The 17 V input is what separates this module from the 6 V family. A 12 V rail with a plus or minus 10 percent tolerance reaches 13.2 V, and a 15 V rail reaches 16.5 V, both inside the range with margin. The same module on a 24 V bus is outside the rating, and a buyer who reads the 3 A current first and the voltage second will make that mistake once.
Soft start and tracking share one pin, so the capacitor value is a compromise when both are used. A larger capacitor slows the ramp and softens the inrush, and it also slows the tracking response when the pin is driven from another rail. In a tracking arrangement the driving source sets the ramp and the capacitor only filters, so a small value is the right choice.
The eight pin outline is shared across the family, which makes a power upgrade a bill of materials change. The pin functions stay in the same places, so a board built for a lower current member can carry this one when the load grows. That is worth knowing at the drawing stage, because the alternative is a second board revision for two amps. The footprint, the pad and the pin functions are what carry over, so the eight pin outline is the part of the family that is actually reusable.
Three amps in a 3 mm body relies on the copper under it. The module has a thermal pad and the heat leaves through the board, so the number of vias and the plane it connects to decide the junction temperature. A board that copies the pad footprint but connects it to a thin trace will run the module hot at half its rated current.
Where this order code fits
These modules power industrial controllers, telecom line cards, solid state drives and networking equipment that run from a 12 V or 15 V bus and need a compact 3.3 V, 1.8 V or 1.2 V rail with a controlled ramp. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can it run from 12 V directly? Yes, the input range is 3 V to 17 V, so a 12 V rail with tolerance fits. The dissipation at 12 V in and a low output is the limit, not the voltage rating.
What is the SS/TR pin for? It sets the soft start ramp with a capacitor, and it also accepts an external ramp so this rail tracks another supply during power up.
Is a 0.8 V output possible? No, the adjustable range starts at 0.9 V. A 0.8 V core rail needs a different device.
Can it take a 24 V input? No. The input range is 3 V to 17 V, so a 24 V bus needs a different module or a pre regulator.
How does tracking work in practice? A capacitor on SS/TR sets the ramp for a normal start, and an external voltage on the same pin makes the output follow that voltage. The pin cannot do both at once, so the choice is made by the circuit around it.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.