Contact Us

TPS7A9401DSCR

Brand: Texas Instruments
Texas Instruments TPS7A9401DSCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A9401DSCR — Power Management & Signal Chain | Superb Automation

TPS7A9401DSCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A9401DSCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A9401DSCR: a 1 A rail that can be taken all the way to zero

The TPS7A9401DSCR is a 1 A regulator whose output can be set anywhere from 0 V to 5.5 V, which is unusual and useful. Most regulators stop at a 0.8 V reference and cannot reach zero at all; this one can be pulled to 0 V by the divider, so a rail can be shut down completely rather than parked at a residual voltage. Noise is 0.46 uV RMS over 10 Hz to 100 kHz and rejection is 110 dB at 1 kHz, 95 dB at 10 kHz, 78 dB at 100 kHz and 50 dB at 1 MHz.

The input range is 1.7 V to 5.7 V, dropout is 150 mV at 1 A, and the part is built to be paralleled: two or more devices share current through their programmable current limit settings, which halves the noise and doubles the available current without a ballast resistor. Precision enable with its own UVLO threshold, a programmable power-good threshold and an adjustable soft start complete the control set.

Key electrical data for the 1 A part

Input range1.7 V to 5.7 V, with 500 mV of headroom at 750 mA for the quoted rejection
Output range0 V to 5.5 V adjustable through the external divider
Output current1 A per device, current limit programmable rather than fixed
Dropout150 mV at 1 A, which sets the minimum input for a regulated 3.3 V rail
Noise0.46 uV RMS from 10 Hz to 100 kHz, the lowest figure in this family
Rejection110 dB at 1 kHz, 95 dB at 10 kHz, 78 dB at 100 kHz, 50 dB at 1 MHz
Parallelingtwo or more devices share current for lower noise and higher output current

Package, marking and reel data

BodyWSON DSC, 10 pins, 3.00 mm by 3.00 mm, thermal pad on the underside
Reel3000 pieces, large tape and reel, 330 mm carrier
Finish and moistureNIPDAU, level 1, 260 C peak reflow, unlimited floor life
Marking7A9401
Companion partthe 2 A member of the same line is available in the identical body and pin out

Where a 0.46 uV rail is spent

Test and measurement instruments, medical imaging front ends, high resolution data converters and radar receivers are the applications where a supply at half a microvolt of noise changes a specification rather than a datasheet line. A 16 bit converter with a 2 V reference resolves about 30 uV per code, so a supply carrying 5 uV of noise into its reference pin is a measurable part of the error budget. At 0.46 uV the regulator stops being a contributor.

The zero volt capability is the other half. Some sensors and laser drivers must be brought up and down in a controlled order, and a rail that can be driven to exactly 0 V, with a programmable ramp, removes a load switch from the path and its on resistance from the accuracy budget. Paralleling two devices takes the noise down by a further 3 dB when one is not enough, which is why the current limit is a setting rather than a fixed number. The 1 A and 2 A members share a body and a pin out, so a board can be laid out once and populated according to the current the load finally needs.

Buyer questions on the TPS7A9401DSCR

How does the part reach 0 V when other regulators stop at 0.8 V? The reference is level shifted so the feedback node can be taken to ground, and the pass element is a floating structure that does not need headroom. The divider sets the point, and a rail at 0 V is a valid setting rather than a shutdown state.

What has to match when two devices are paralleled? The current limit settings, which are programmed per device, and the output sense connections. The loop then shares the load without an external ballast resistor, and the combined noise falls as the square root of the device count.

Is the power-good threshold fixed? No, it is programmable, which lets a supervisor flag a rail that has fallen a chosen percentage below its set point instead of a fixed 90 percent. That matters on a converter supply where a 5 percent dip is already a fault.

Buying this regulator through a component supplier

A 0.46 uV regulator at 3000 pieces per reel is a long lead item when the market is tight, and it is rarely a part a customer can substitute quickly because the noise figure is the reason it was chosen. Our component obsolescence management page covers the buffer and last time buy route. To compare the 1 A and 2 A members by body, power management cross reference lists them side by side.