Contact Us

TPS7A8701RTJR

Brand: Texas Instruments
Texas Instruments TPS7A8701RTJR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A8701RTJR — Power Management & Signal Chain | Superb Automation

TPS7A8701RTJR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A8701RTJR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A8701RTJR: a dual 500 mA low noise linear regulator with two independent channels in a 4 mm body

TPS7A8701RTJR is a dual channel low dropout regulator with 3.8 microvolt rms noise, two open drain power good outputs and a 0.8 V reference in a WQFN (RTJ) body of 20 pins. It holds two independent rails at 500 mA each with 100 mV of maximum dropout, from an input as low as 1.4 V and as high as 6.5 V, and the output of each channel is set from 0.8 V to 5.2 V by its own divider. Noise is 3.8 microvolt rms over 10 Hz to 100 kHz, rejection is 75 dB at DC and 40 dB at 100 kHz, and accuracy is 1 per cent over line, load and temperature. Each channel has its own enable, its own soft start control and its own power good output, so two rails can be sequenced without a second part.

Order code and package

TPS7A8701RTJRWQFN body of 20 pins measuring 4.00 mm by 4.00 mm, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 1 at 260 C with unlimited floor life, marking TPS7A87, active status in the package addendum
TPS7A8701RTJTthe same die on a 250 piece small reel, which is the string a pilot or a repair bench orders
G4 rowthe same string with a green material declaration, 3000 pieces on a large reel, which is the row a customer with a material requirement asks for
Channelstwo independent regulators sharing only the package, the ground and nothing else: separate input, separate output, separate enable, separate power good
Noise reduction pinone per channel, and a capacitor on it lowers the reference noise further, which is why the pin exists at all
Soft start controlone pin per channel selects the charging current, so the ramp is a choice between two rates rather than a fixed value

Electrical parameters that decide the application

Input voltage1.4 V to 6.5 V per channel, which covers a 1.8 V, 2.5 V, 3.3 V or 5 V rail as both the input and the output
Output voltage0.8 V to 5.2 V per channel, set by a divider against a 0.8 V reference with 1 per cent accuracy over line, load and temperature
Output current500 mA per channel, with 100 mV of maximum dropout at that current, so a 1.2 V rail needs 1.3 V in and a 3.3 V rail needs 3.4 V
Noise3.8 microvolt rms over 10 Hz to 100 kHz at the stated test condition, which is the figure that decides whether the part can feed a converter or a reference directly
Rejection75 dB at DC and 40 dB at 100 kHz and at 1 MHz, which is the property that keeps a switching regulator's ripple out of an analog rail
Current limit1.1 A minimum and 1.5 A maximum per channel, which is a foldback style limit that protects the pass element during a fault
Ground current2.1 mA typical and 3.5 mA maximum per channel at 500 mA, with 0.1 microamp to 15 microamp in shutdown depending on the row
Enable thresholds1.1 V to enable and 0.4 V to disable, so a 1.2 V or 1.8 V logic line drives the pin directly
Power goodopen drain per channel, with the threshold set inside the part and referenced to the output, so the signal follows the rail rather than a fixed voltage
Soft startselectable charging current, which sets two ramp rates and therefore two inrush currents
Lockouteach input has its own undervoltage lockout at 1.31 V to 1.39 V rising, so a channel does not start on a rail that is still coming up
Thermal33 C per watt junction to ambient in the 20 pin body, which is low for a linear regulator and is the reason the part can hold 500 mA on both channels

What each channel includes and what the pair shares

TPS7A8701RTJRthe dual 500 mA regulator covered by this order code, 20 pins on 4 mm by 4 mm, 3000 pieces on a large reel
TPS7A8701RTJTthe same die on a 250 piece small reel, and the G4 row carries a green material declaration on the large reel
Channelstwo independent rails with separate input, output, enable, soft start control and power good, sharing only the package and ground
Noise reductionone pin per channel, and a capacitor on it lowers the reference noise below the 3.8 microvolt rms figure
Dropout100 mV maximum at 500 mA over temperature, which is the number a 1.2 V rail from a 1.5 V source is planned against
Rejection75 dB at DC and 40 dB at 100 kHz, which is the figure that applies to a switching regulator in front of the linear part
Thermal33 C per watt for the package, so both channels at full current are added together against the ambient

Points to check before this part goes on a BOM

Two channels in one body share a thermal budget. The 33 C per watt figure is per package, so both channels at 500 mA add their dissipation. A 3.3 V to 1.8 V rail at 500 mA is 0.75 W on its own, and two of those in a 4 mm body need the pad copper and the ambient checked together.

The 100 mV dropout is a maximum, not a typical. That is the number to plan a rail against, because it holds at 500 mA and over temperature. A 1.8 V rail from a 2.5 V input has far more margin than it needs, and a 1.2 V rail from a 1.8 V input is still inside the window.

Noise and rejection are two different specifications. 3.8 microvolt rms is the noise the part generates, and 40 dB at 100 kHz is what it removes from the input. A rail that is quiet but rejects poorly passes the input ripple straight through, so both figures matter on a converter rail.

The noise reduction pin is not optional on a sensitive rail. A capacitor on it lowers the reference noise, and leaving it open gives the datasheet figure at best. It is also the pin that a board copies wrong most often, because it looks like a bypass and is treated as one.

Power good is per channel and referenced to the output. Each output has its own open drain signal, so a system can sequence one rail on the other without adding a supervisor. The pull-up may go to a rail other than the input, which is what allows a 1.8 V signal from a 3.3 V regulator.

The 1.4 V input floor is a real limit for a 0.8 V rail. A 0.9 V core rail from a 1.0 V source is inside the electrical window on paper, and in practice the dropout plus the accuracy leaves very little. A rail that close needs the dropout curve checked at the actual current.

Why two channels in one package

An analog front end usually needs a positive rail and a quiet reference rail, or a 3.3 V digital rail and a 1.8 V analog rail. Two single regulators take twice the area and twice the placement, and they do not share a thermal pad or a ground reference.

Putting both in one body also removes the question of which rail comes up first, because the enables and the power good signals are on the same part and can be wired against each other on the board.

Reading a low noise regulator specification

The noise figure is quoted over a bandwidth and at a current, and both matter. A part that quotes 3.8 microvolt rms at 500 mA is not the same as one that quotes the same number at 1 mA, because the noise of the reference and the error amplifier changes with the operating point.

The rejection figure is quoted at frequencies, and a switching regulator in front of the linear part puts its ripple at a specific frequency. The 40 dB at 100 kHz is the number that applies to a 100 kHz converter, and a converter at 2 MHz needs the figure at 2 MHz instead.

Where this order code fits

an analog front end, a data converter supply or a medical monitor that needs two quiet rails with separate sequencing Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Can both channels run at 500 mA at the same time? Electrically yes, and the package dissipation is the limit. The 33 C per watt figure covers both channels, so the ambient and the drop across each pass element have to be added together before the current is fixed.

How is the output set? By a divider against a 0.8 V reference on each channel, from 0.8 V to 5.2 V, with 1 per cent accuracy over line, load and temperature.

What dropout does it need? 100 mV maximum at 500 mA over temperature, so a 1.2 V rail needs at least 1.3 V in and a 3.3 V rail needs 3.4 V.

Does it have a noise bypass pin? Yes, one per channel. A capacitor on it lowers the reference noise below the 3.8 microvolt rms figure, and leaving it open gives the datasheet number at best.

Are the power good outputs independent? Yes, one open drain per channel, and the pull-up may go to a different rail than the input, which allows a low voltage logic signal from a higher rail.

What packing is available? 3000 pieces on a large reel for the R suffix, 250 pieces on a small reel for the T suffix, and a G4 row with a green material declaration on the same 3000 piece reel.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.