TPS7A8500RGRR
Product Specifications
TPS7A8500RGRR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A8500RGRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A8500RGRR: the plain 4 A die at 1 percent accuracy
The TPS7A8500RGRR is the original TPS7A85 order code, a 4 A regulator with 4.4 uV RMS of noise at 0.8 V, 240 mV of maximum dropout and 1 percent accuracy over line, load and temperature. It sets its output between 0.8 V and 3.95 V with board straps, or between 0.8 V and 5.0 V with an external divider, and it is stable with 47 uF or more of ceramic output capacitance. In the 3.5 mm RGR body the marking is 11DI, and the reel carries 3000 pieces.
Against the A revision the differences are small and specific: the accuracy window is 1 percent rather than 0.75, the divider range stops at 5.0 V rather than 5.1 V, and the noise figure is quoted as 4.4 uV at 0.8 V and 8.4 uV at 5.0 V. For a digital core rail at 1.0 V, or an analog rail at 3.3 V, none of those differences changes a decision. For a 5 V bias that has to sit at the very edge of the divider range, they do.
Key electrical data for the 4 A part
| Input range | 1.4 V to 6.5 V without bias, 1.1 V to 6.5 V with the bias rail supplied |
| Output range | 0.8 V to 3.95 V by board straps, 0.8 V to 5.0 V with an external divider |
| Output current | 4 A, with remote sense to compensate trace and via resistance |
| Dropout | 150 mV typical and 240 mV maximum at 4 A |
| Accuracy | 1 percent maximum over line, load and temperature |
| Noise | 4.4 uV RMS at 0.8 V, 8.4 uV RMS at 5.0 V, over 10 Hz to 100 kHz |
| Rejection | 40 dB at 500 kHz, with 47 uF of ceramic output capacitance for stability |
Package, marking and reel data
| Body | VQFN RGR, 20 pins, 3.50 mm by 3.50 mm, exposed thermal pad |
| Reel | 3000 pieces, large tape and reel, 12.4 mm tape on a 330 mm carrier |
| Finish and moisture | NIPDAU, level 1, 260 C peak reflow, unlimited floor life |
| Marking | 11DI |
| Small quantity option | RGRT carries 250 pieces on a 180 mm carrier |
Where the plain 4 A part is the better buy
Most 4 A linear rails are post regulators behind a buck, and in that position the headroom is set by the buck tolerance rather than by the load. A 1.2 V buck feeding a 1.0 V rail leaves 200 mV plus the buck's own window, which is why the 240 mV dropout figure matters more than the accuracy figure. At 4 A and 300 mV the part burns 1.2 W, and the 3.5 mm body with a proper pad holds the junction about 25 C above the board.
The plain part is also the one already on many approved lists, which is a real advantage when a customer is copying a proven supply block into a new board. Changing to the A revision buys 0.25 percent of accuracy and 0.1 V of range; if the rail does not need either, the plain code avoids a re-qualification step that costs more than the parts. What a buyer should check first is the accuracy window on the rail, not the revision letter on the reel label: at 3.3 V a 1 percent window is 33 mV, which is usually inside the load tolerance, and at 0.9 V the same window is 9 mV, which often is not.
Buyer questions on the TPS7A8500RGRR
Can the two revisions be mixed on one board? Electrically the pins and the strap table are the same, so a board built with either works. The mixture does break traceability of the accuracy window, so a rail that is specified at 0.75 percent should be built with the A code only.
What is the purpose of the soft start pin? It sets the ramp of the output by an external capacitor, which limits the inrush into the 47 uF output and keeps the upstream converter out of current limit at power up. The SS/TR pin can also be used to track another rail.
How much headroom does the part need at 4 A? 240 mV maximum at the specified dropout, plus the tolerance of the input rail. Below that the output follows the input down, which is acceptable for a core rail and not acceptable for a reference.
Buying this regulator through a component supplier
A 4 A regulator at 3000 pieces per reel is bought against a build schedule, and the risk is the reel change landing in the middle of a run. Our component lead time solutions covers partial reels and split shipments. The power management cross reference lists the family members by body so a second source can be checked without reopening the whole supply tree.