Contact Us

TPS7A6650QDGNRQ1

Brand: Texas Instruments
Texas Instruments TPS7A6650QDGNRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A6650QDGNRQ1 — Power Management & Signal Chain | Superb Automation

TPS7A6650QDGNRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A6650QDGNRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A6650QDGNRQ1: automotive 5 V, 150 mA regulator with 12 uA quiescent current and a reset output

TPS7A6650QDGNRQ1 is a high voltage linear regulator that stays on the battery rail and reports its own output state to a microcontroller in a HVSSOP (DGN) body of 8 pins. It takes 4 V to 40 V in, delivers 150 mA at 5 V with 1 per cent accuracy at room temperature and 2 per cent over the full range, draws 12 uA typical and 20 uA maximum of quiescent current, and adds an open drain reset output that holds a processor in reset until the rail is valid.

Order code and package

Ordering stringTPS7A6650QDGNRQ1, the 5 V fixed output in the 8 pin HVSSOP
Body8 pin HVSSOP with a thermal pad, 3.00 mm by 3.00 mm
Second body in the family8 pin SOIC, 4.90 mm by 3.91 mm, used on the TPS7A69-Q1 members
QualificationAEC-Q100 grade 1 as standard, with the E marked order code qualified to grade 0 for the wider temperature band
Fixed outputs5 V and 3.3 V versions, plus an adjustable member with a 1.223 V band gap reference
Reset outputOpen drain, with a delay set by an external capacitor, holding the processor until the output is valid
Temperatureminus 40 to 150 degrees junction

Electrical parameters that decide the application

Input range4 V to 40 V, with the fixed 5 V version specified from 5.5 V in for full regulation and the fixed 3.3 V version from 4 V
Output current150 mA, with the current limit window at 300 to 450 mA
Accuracy1 per cent at 25 degrees, 2 per cent over 1 mA to 150 mA and the full temperature range
Quiescent current12 uA typical, 20 uA maximum with the enable high and no load
Sleep current4 uA maximum with the enable low, which is the figure that matters for a module that has to wake on a CAN frame
Dropout300 mV at 150 mA, 180 mV typical and 240 mV maximum at 80 mA
Line and load regulation5 mV over 5.5 V to 40 V in, 20 mV over 1 mA to 150 mA
Ripple rejection58 dB at 100 Hz with a 2.2 uF output capacitor and 10 mA of load
Band gap reference1.223 V typical, 1.199 to 1.247 V, which sets the accuracy of the adjustable member
Undervoltage lockout2.6 V typical with 1 V of hysteresis, so a cold crank does not chatter the output
Enable thresholds1.7 V minimum for a high, 0.4 V maximum for a low, 1 uA of input current
ThermalThe HVSSOP pad is the heat path; at 150 mA from a 13.5 V battery into 5 V the part dissipates about 1.3 W

Family variants and how they differ

TPS7A6650 against the adjustable memberThis page is the 5 V fixed version. The adjustable member uses an external divider into a 1.223 V reference, and its accuracy is quoted over the same 2 per cent window
Grade 0 order codeThe E marked code is qualified to AEC-Q100 grade 0, which extends the ambient range beyond grade 1. A board that has to run in the engine bay rather than the cabin needs that code, not this one
Reset delaySet by a capacitor on the delay pin. The reset asserts as soon as the output falls out of regulation and releases after the delay once the output is valid again
HVSSOP against SOICThe HVSSOP body has the thermal pad and the lower junction to ambient figure. The SOIC body is easier to inspect and is used on the TPS7A69 members
Quiescent current across the family12 uA is low for a 40 V part but not the lowest in the market; the TPS7B81 family reaches 2.7 uA. The difference buys the reset output and the wider input rating
No reverse protectionThere is no reverse battery protection inside. A series diode or a P-channel FET is still needed on a battery rail that can be connected backwards during service

Points to check before this part goes on a BOM

The sleep current of 4 uA is a maximum, and it is the number that decides battery life on a module that is enabled by a wake line. The 12 uA operating figure applies only while the regulator is on.

Dropout is 300 mV at 150 mA. On a cold crank that pulls the battery to 5.3 V, the 5 V output holds; below about 5.3 V it follows the input down, and the reset output is what tells the processor to stop cleanly.

The 1 per cent accuracy belongs to 25 degrees. Over the full range the window is 2 per cent, which is what a CAN transceiver supply has to be checked against, not the headline figure.

The reset output is open drain and needs a pull up. Its timing is set by an external capacitor, so the release delay is a component choice rather than a fixed number.

The HVSSOP pad carries the heat. At 13.5 V in and 5 V out at 150 mA the part dissipates 1.3 W, and without a pad tied to a copper area the junction reaches the thermal limit quickly.

The 40 V input rating is an operating figure. Load dump on a 12 V system reaches far higher unless the vehicle has a central clamp, and the clamp is part of the system rather than the regulator.

Why a reset output matters more than a microamp

A microcontroller that loses its supply without a reset can start executing from a random address when the rail comes back, and in a body control module that means a relay or a lamp in an undefined state. A regulator with a reset output asserts the processor reset while the output is out of regulation and holds it for a set delay after the rail is valid.

That function is normally a separate supervisor plus a regulator. Putting it in one 3 mm package removes a part, a node and a tolerance stack. The cost is a slightly higher quiescent current than the lowest power regulators in the same voltage class.

Where this order code fits

Body control modules, gateways, remote keyless entry receivers, immobilisers and infotainment units that stay connected to the battery when the ignition is off. The reset output is the reason many of these boards use this part rather than a plain regulator: the microcontroller needs a defined reset while the battery rail ramps and while a cold crank pulls it down. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the OEM Procurement page.

Questions buyers ask

What is the difference between this part and a TPS7B8133? Both are 40 V automotive regulators. This one has a reset output and 12 uA of quiescent current; the TPS7B81 family has 2.7 uA and no reset. A board that needs a supervisor takes this part, a board that only needs the rail takes the other.

How long is the reset delay? It is set by the capacitor on the delay pin. The data sheet gives the charging current and threshold, so the delay is calculated rather than selected from a table.

Can the output be used below 4 V in? The fixed 5 V member is specified from 5.5 V in for full regulation, and the fixed 3.3 V member from 4 V. Below those points the output follows the input minus dropout.

Does the enable pin fully disconnect the load? It puts the part into a 4 uA sleep state, not a true disconnect. A load that must be isolated needs an external switch.

Is the adjustable member a drop-in? Same body and same pinout, but the feedback pin becomes an input and the divider sets the output. The board has to change, so the two are not interchangeable without a revision.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.