Contact Us

TPS7A4350DGQR

Brand: Texas Instruments
Texas Instruments TPS7A4350DGQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A4350DGQR — Power Management & Signal Chain | Superb Automation

TPS7A4350DGQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A4350DGQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A4350DGQR: the fixed 5 V member of the 85 V family

The TPS7A4350DGQR is the 5.0 V fixed output of the TPS7A43 line, built in the same 10 pin HVSSOP body as the adjustable version and sharing its 4 V to 85 V input window. The 50 in the order code is the factory trim, so the rail is 5 V at 1 percent and no divider is needed. That matters less for the accuracy than for the pin count and the leakage: a fixed part frees the feedback node, removes two resistors from a high voltage net, and keeps the quiescent current at 5.5 uA typical instead of the few microamps a divider would add.

The rest of the family behaviour carries over unchanged. MID_OUT can be strapped to 10 V, 12 V or 15 V, which on a 24 V bus is enough to bias a MOSFET gate driver while the 5 V rail runs the logic. Dropout from the input to OUT is 800 mV maximum at the full 50 mA, from MID_OUT to OUT it is 200 mV, so a cascade from 48 V to 12 V to 5 V keeps the second stage out of dropout until the input falls below about 5.2 V.

Key electrical data for the 5 V point

Input range4 V to 85 V continuous, the same silicon as the adjustable member
Output5.0 V fixed, 1 percent over temperature, 0.5 percent at 25 C
Output current50 mA shared with MID_OUT, 500 mA of inrush tolerated by the current limit
Line and load regulation0.05 percent across the full 4 V to 85 V input swing, 0.10 percent from 1 mA to 50 mA
Quiescent current5.5 uA typical at no load, 9 uA at 50 mA, 710 nA in shutdown at 25 C
Protectioncurrent limit on both outputs, thermal shutdown, reverse current blocking through the pass element

Package, marking and reel data

BodyHVSSOP DGQ, 10 pins, 3.00 mm by 3.00 mm with an exposed pad
Reel2500 pieces, 330 mm carrier, 12.4 mm tape
Finish and moistureNIPDAUAG, level 2, 260 C peak reflow, one year floor life
Marking4350 on the top of the package
Thermal53.7 C per W junction to ambient, 3.6 C per W junction to case at the pad

Where a fixed 5 V from 85 V earns its place

Industrial sensor nodes on a 24 V loop, relay and contactor coils in a panel, battery management boards on a 16 cell stack, and the auxiliary rail of an EV charger all need a 5 V housekeeping supply that survives a transient far above the nominal bus. The usual answer is a wide input switching regulator followed by a linear part, which costs an inductor and board area of its own. A single 85 V linear regulator replaces that chain when the load is below 50 mA, which is the case for a CAN transceiver, a current sense amplifier and a low power microcontroller.

The limit is dissipation, not voltage. At 24 V in and 5 V out with 30 mA the part burns 570 mW, which the 3 mm body passes to a modest copper area at about 30 C of rise. At 60 V in the same current burns 1.65 W and needs real copper and a cooler ambient. The MID_OUT rail is the tool for that case: take 12 V first, then 5 V, and the dissipation splits across two pass elements in the same package.

Buyer questions on the TPS7A4350DGQR

Is the fixed 5 V part pin compatible with the adjustable one? Yes, both are the 10 pin DGQ body. The fixed version uses the FB pin internally, so the two divider resistors disappear and the board keeps the same footprint if a later build needs the adjustable member instead.

How is the 10 V, 12 V or 15 V intermediate rail chosen? Two MVSEL pins set it in hardware, with no resistor and no register. The tolerance is 4 percent, which is enough for a gate driver bias and not enough to be used as a precision reference.

Does the part need an output capacitor for stability? The data sheet specifies 1 uF on OUT and 4.7 uF on MID_OUT, both ceramic, and the transient figures assume those values. A smaller output capacitor can make the loop ring at the load step.

Buying this regulator through a component supplier

The high voltage linear regulators a customer keeps on an approved list are usually three or four order codes from two vendors, and substitution between them turns on the body and the pin out rather than on the voltage. The power management cross reference lists those rows by body. For a build that cannot wait for a factory lead time, safety stock planning covers the buffer quantity and the date code rule for the buffer reel.