TPS7A4301DGQR
Product Specifications
TPS7A4301DGQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A4301DGQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A4301DGQR: an adjustable 85 V regulator that still draws 5.5 uA
The TPS7A4301DGQR is the adjustable member of the TPS7A43 line, a linear regulator that takes 4 V to 85 V at the input and holds its output anywhere between 1.24 V and 14.5 V. What separates it from the usual 40 V part is not the voltage alone. The quiescent current is 5.5 uA typical and 7 uA maximum at 25 C, and that figure survives a rail sitting at 60 V or 72 V. A 15 cell battery stack or a 48 V line card can therefore feed a housekeeping rail without a pre regulator and without a standing drain that empties the pack over a weekend.
The second output is the unusual feature. A MID_OUT pin delivers a fixed 10 V, 12 V or 15 V selected by two MVSEL pins, and that intermediate rail can bias a gate driver or a relay coil directly. The 50 mA rating is shared between the two outputs, so a load budget has to be written for the pair rather than for each one. Current limit is 125 mA typical on OUT and 145 mA typical on MID_OUT, and both are protected against a short to ground.
Key electrical data for the adjustable version
| Input range | 4 V to 85 V, with no pre regulator needed on a 48 V or 60 V rail |
| Output range | 1.24 V to 14.5 V adjustable through the FB pin, 1 percent accuracy over temperature |
| Output current | 50 mA shared with MID_OUT, limit 100 mA to 145 mA on OUT and 118 mA to 165 mA on MID_OUT |
| Quiescent current | 5.5 uA typical, 7 uA maximum at 25 C, 9 uA at the full 50 mA load |
| Shutdown current | 710 nA typical at 25 C, 1.6 uA maximum over the full temperature range |
| Dropout | 800 mV maximum from VIN to OUT at 50 mA, 200 mV from MID_OUT to OUT, 600 mV into MID_OUT |
| Rejection and noise | 76 dB at 10 Hz, 124 uV RMS from 10 Hz to 100 kHz at a 1.24 V output |
Package, marking and reel data
| Body | HVSSOP DGQ, 10 pins, 3.00 mm by 3.00 mm, thermal pad underneath |
| Reel | 2500 pieces, 330 mm carrier, 12.4 mm tape |
| Finish and moisture | NIPDAUAG, level 2, 260 C peak reflow, one year floor life |
| Marking | 4301 on the top of the package |
| Thermal | junction to ambient 53.7 C per W, so 1 W of dissipation lifts the die by about 54 C |
Where an 85 V input belongs
The obvious homes are cordless power tools at 18 V to 60 V, programmable logic controllers running from a 24 V bus that sees 60 V transients, field transmitters, smoke and heat detectors, and the housekeeping rail of an EV charging pile. In each of those the input moves by tens of volts during a hot plug or a load dump, and a regulator rated at 40 V needs a clamp in front of it. An 85 V part removes that clamp and its leakage, and the 1.24 V floor lets the same part generate a 1.8 V logic rail and a 12 V gate bias from one order code.
The thermal budget sets the limit here rather than the current. At 50 mA from 48 V into 3.3 V the part burns 2.2 W, which no 3 mm package survives without a copper pour. That is not a fault of the device, it is the arithmetic of a linear pass element, and the honest way to use this part above 24 V is to take the drop in two steps, using MID_OUT at 15 V for the coarse step and OUT for the fine one. The 200 mV dropout from MID_OUT to OUT makes that second step cheap.
Buyer questions on the TPS7A4301DGQR
Can the output be trimmed after the board is built? Yes, the adjustable version sets its output with the feedback divider, so a resistor change moves the rail. The fixed members of the family, 1.25 V to 5.0 V, cannot be moved at all, and the two versions share the same body and pin count.
What sets the power-good threshold? The PG pin is an open drain output that pulls low when the feedback voltage falls below 90 percent of its nominal value, with 3 percent of hysteresis. It needs an external pull up, and it can sequence a second regulator without a supervisor part.
Why is the enable pin called precision? The threshold is specified tightly enough to use a resistor divider from the input as an undervoltage lockout. The part stays off until the divider crosses the threshold, which keeps a 48 V rail from starting the load during a slow rise.
Buying this regulator through a component supplier
An 85 V regulator is bought in reels of 2500 and is usually one line of a larger power tree, so the useful comparison is against the other high voltage parts a customer already has on the approved list. Our power management cross reference puts those rows side by side by body and pin count. When a reel is short and the build date is fixed, the route through component lead time solutions covers partial reels and date code control on the shipment.