Contact Us

TPS7A4001MDGNREP

Brand: Texas Instruments
Texas Instruments TPS7A4001MDGNREP is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A4001MDGNREP — Power Management & Signal Chain | Superb Automation

TPS7A4001MDGNREP

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A4001MDGNREP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A4001MDGNREP: the 100 V regulator in its enhanced product form

The TPS7A4001MDGNREP is the enhanced product version of the TPS7A4001, a 50 mA linear regulator that withstands 100 V at the input and sets its output from about 1.175 V to 90 V through a divider. The M in the code marks the enhanced product flow, the DGN is the eight pin HVSSOP body with a PowerPAD, and the EP suffix is the programme itself: one assembly and test site, one fabrication site, a controlled baseline, extended change notification and full traceability.

The electrical difference from the commercial part is small but documented. The overall accuracy over line, load and temperature is 2.7 percent rather than 2.5 percent, the temperature range extends to minus 55 degrees at the cold end, and the qualification flow follows the defence and aerospace route rather than the industrial one. The package, the pinout and the 100 V rating are otherwise the same.

Key electrical data for the enhanced product

Input range7 V to 100 V continuous, with transient capability stated separately in the data sheet
Output rangeabout 1.175 V to 90 V adjustable, 50 mA maximum
Quiescent current25 uA typical, 4.1 uA in shutdown
Accuracy1 percent nominal at 25 C, 2.7 percent over line, load and temperature
Dropout290 mV typical, measured at 20 mA with the input at 17 V into an 18 V output
Rejection65 dB at 100 Hz with a 10 nF bypass capacitor across the feedback network
Noise58 uV RMS at the reference voltage, 73 uV RMS at 5 V output with the same bypass

Package, marking and reel data

BodyHVSSOP DGN, 8 pins, 3.0 mm by 5.0 mm, PowerPAD
Reel2500 pieces, large tape and reel, 330 mm carrier, 12 mm tape
FinishNIPDAUAG, moisture level 2, 260 C, one year floor life
MarkingZFY4
Temperatureminus 55 to 125 C, wider than the commercial 40 to 125 C of the base part

Where a 100 V linear regulator belongs

The application is a low voltage rail derived from a high voltage bus that sees transients: industrial automation with 48 V or 72 V rails, telecom line cards, power over Ethernet front ends, LED drivers and bias supplies. In those circuits the regulator's job is not efficiency but survival, and a part rated at 100 V continuous lets the engineer stop worrying about the clamp voltage of the transient suppressor.

The limit is dissipation, as with every linear regulator at high input. At 48 V in and 5 V out the part drops 43 V, so at 20 mA it dissipates 860 mW and at 50 mA it dissipates 2.15 W. The HVSSOP with a PowerPAD handles the first figure with a copper plane and needs a thermal calculation for the second. In practice the part is used at a few milliamps to bias a controller, not to power a load, and the 50 mA rating is there for short bursts and for start up inrush. The enhanced product flow exists because defence and aerospace programmes need the same behaviour with a documented supply chain behind it.

Buyer questions on the enhanced product code

What does the enhanced product programme add? One fabrication and assembly site, a controlled baseline, extended product change notification, product traceability and a military temperature range. The silicon is the same as the commercial part.

Is the commercial part a drop in substitute? Electrically it is close, with 2.5 percent accuracy and a minus 40 degree cold end. For a defence or aerospace build the programme requirements usually rule it out even where the electrical window would allow it.

Does the part need the bypass capacitor? The rejection and noise figures quoted here assume a 10 nF capacitor across the feedback network. Without it the part still regulates, but the rejection at 100 Hz falls and the noise rises.

Sourcing enhanced product parts

Enhanced product and military temperature parts cannot be bought from the open market without paperwork, and a reel with no traceability is worthless on a defence programme. Defense grade components sets out what we require before quoting, and incoming inspection plan describes the checks applied to a 2500 piece shipment.

The enhanced product flow is the reason this code exists rather than the base part number. It brings one fabrication site, one assembly and test site, a controlled baseline, extended product change notification, product traceability and a minus 55 degree cold end, and the accuracy window widens to 2.7 percent to cover the extra range. The silicon is otherwise the commercial part. A programme that needs the base part can use it, and a programme that needs the documented supply chain cannot, which is a paperwork difference rather than an electrical one. The 2500 piece reel and the moisture level 2 floor life match the commercial part, so a programme that moves to the enhanced flow keeps its reflow profile and its feeder setup.