Contact Us

TPS7A3001DRBR

Brand: Texas Instruments
Texas Instruments TPS7A3001DRBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A3001DRBR — Power Management & Signal Chain | Superb Automation

TPS7A3001DRBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A3001DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A3001DRBR: negative 200 mA linear regulator with 15 uV of noise from a -35 V input

TPS7A3001DRBR is a negative low dropout regulator that produces a clean negative rail for analog circuits from an input as low as -3 V and as high as -35 V in a VSON body of 8 pins. The TPS7A3001 is a negative linear regulator that takes -3 V to -35 V in and sources up to 200 mA, with an output adjustable from the -1.179 V reference up to -33 V. Its noise is 15.1 uV root mean square from 10 Hz to 100 kHz and 14 uV from 20 Hz to 20 kHz, and its ripple rejection is 72 dB at 120 Hz and at least 55 dB at 10 kHz. Overall accuracy is plus or minus 2.5 percent, dropout is 325 mV typical at 200 mA, and the body is an eight pin VSON.

Order code and package

Order codeTPS7A3001DRBR
Input voltage-3 V to -35 V
Output current200 mA
Output voltage-1.179 V to -33 V, set by a divider
Reference-1.179 V to -1.202 V, -1.166 V minimum
Noise15.1 uV root mean square from 10 Hz to 100 kHz
Ripple rejection72 dB at 120 Hz, at least 55 dB at 10 kHz
Accuracyplus or minus 2.5 percent overall
Dropout216 mV at 100 mA, 325 mV typical and 600 mV maximum at 200 mA
Current limit220 mA minimum, 330 mA typical, 500 mA maximum
Package8 pin VSON
Soft startcapacitor programmable on the noise reduction pin
DocumentTPS7A30 series data sheet

Electrical parameters that decide the application

Line regulation0.14 percent of output over the full input range
Load regulation0.04 percent of output from 1 mA to 200 mA
Thermal resistance, 8 pin VSON47.7 C per W junction to ambient
Thermal resistance, 8 pin MSOP63.4 C per W junction to ambient
Junction range-40 C to 125 C
EnableCMOS logic level, referenced to the input
Output capacitor2.2 uF ceramic minimum
Noise reduction capacitorreduces noise and sets the soft-start ramp
Topologynegative low dropout, current sourced from the input to ground
Protectioncurrent limit and thermal shutdown
Reference bypassthe noise pin can be tied to the reference for lowest noise
Standbyenable pin takes the part into a low current state

Points to check before this part goes on a BOM

A negative regulator is not a mirror image of a positive one, and the first surprise is the current path. This part sources current from the output node into ground, so the input is more negative than the output and the load current returns through the ground pin. A board that carries over the capacitor polarity and the diode orientation from a positive regulator will not work, and in the worst case it will reverse bias the output capacitor.

Fifteen microvolts of noise is the reason to pay for this part instead of a general purpose negative regulator. On a bipolar analog front end with a 10 V full scale and 16 bit resolution, one code is 153 uV, so the regulator noise is an order of magnitude below the converter resolution and does not show up in the noise floor. A regulator with 100 uV of noise would be visible at that resolution.

Ripple rejection of 72 dB at 120 Hz is aimed at the ripple from a rectifier. At 10 kHz it is 55 dB or better, which is the band where a switching supply in front would put its harmonics. The rejection falls further above that, so a board that feeds this regulator from a 500 kHz converter should add an LC filter rather than rely on the regulator alone.

Dropout of 325 mV at 200 mA is low for a 35 V part, and it is what allows a -5 V rail to be produced from a -5.5 V input. The maximum column is 600 mV, so a board that needs guaranteed operation at full current should use the maximum figure, not the typical one, and should account for the tolerance of the input rail.

The noise reduction pin sets both the noise and the soft start. A capacitor from that pin to the input reduces the reference noise and slows the output ramp; a board that needs a fast start with low noise has to choose, because the same capacitor does both jobs. In a bipolar supply that sequences after the positive rail, a slow ramp is usually the right choice.

Thermal behaviour depends on the package. The 8 pin VSON gives 47.7 C per W and the MSOP 63.4 C per W, and at 200 mA with a 10 V drop across the regulator the dissipation is 2 W, which exceeds what either package can carry at a normal ambient. A board that drops 10 V at 200 mA has to spread the drop, either with a series resistor or with a preregulator.

Accuracy of plus or minus 2.5 percent covers line, load and temperature, and it is looser than the positive regulators in the same class. On a rail that sets the reference for an analog chain, the divider should be trimmed or the system calibrated, because 2.5 percent of a 5 V rail is 125 mV and that is a large offset for a precision front end.

Where this order code fits

This order code fits bipolar analog front ends, operational amplifier rails in instrumentation, audio and precision measurement equipment, and any board that needs a quiet negative supply beside a positive one. The 35 V input ceiling covers a -24 V or -28 V rail with margin for the tolerance and the ripple. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Can this regulator produce a positive rail? No. It is a negative regulator, and the input has to be more negative than the output.

What sets the output voltage? An external divider from the -1.179 V reference, which allows any output from -1.179 V down to -33 V.

How much current can it deliver at a 10 V drop? The 200 mA rating is electrical. The thermal limit is lower: at 2 W of dissipation neither package option is comfortable at a normal ambient.

SUPERB supplies this order code with date codes and packing, and the OEM Procurement page sets out what to check when a quiet negative rail has to be kept in production.