Contact Us

TPS7A2030PDQNR

Brand: Texas Instruments
Texas Instruments TPS7A2030PDQNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A2030PDQNR — Power Management & Signal Chain | Superb Automation

TPS7A2030PDQNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A2030PDQNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A2030PDQNR: 300 mA Low Dropout Regulator in a Four Ball Package

TPS7A2030PDQNR is a 300 mA low dropout regulator with a 1.5 percent output tolerance in a 4-ball DSBGA body of 4 pins. It holds 300 mA at 140 mV of dropout, takes 1.6 V to 6.0 V in, and comes in a four ball package of 0.616 mm square, which is smaller than the capacitor it needs on the output.

Order code and package

Ordering stringTPS7A2030PDQNR, DSBGA-4 (DQN), 0.616 mm by 0.616 mm
Second packageSOT-23-5 (DBV), 2.9 mm by 2.8 mm, 30 mV accuracy grade
Input1.6 V to 6.0 V, or output plus 0.3 V, whichever is greater
Output300 mA, fixed options from 0.8 V to 5.5 V
Enableinternal 500 kOhm pulldown, output discharged when disabled
PinsIN, OUT, EN and GND, no bypass or noise pin

Electrical parameters that decide the application

Output toleranceplus or minus 1.5 percent, 30 mV on the SOT-23 grade
Dropout140 mV in the 2.5 V to 5.5 V output band at 300 mA
Line regulation0.03 percent per volt typ
Shutdownoutput discharged through the internal pulldown
Enable pulldown500 kOhm, 6.6 uA at 3.3 V
Thermal resistance54.4 C/W on the SOT-23, 199.6 C/W on the four ball package

Points to check before this part goes on a BOM

A 3.0 V output with 140 mV of dropout needs 3.14 V at the input, and a 3.3 V rail at minus 5 percent is 3.135 V, which is 5 mV short. The regulator therefore leaves dropout at full 300 mA on a rail that is still inside its own specification, and the 1.5 percent output tolerance cannot be assumed once the pass device is in dropout.

The two packages carry the same silicon and very different thermal numbers: 54.4 C/W for the SOT-23 and 199.6 C/W for the four ball part. Dropping 6 V to 3 V at 300 mA is 0.9 W, which is a 49 C rise in one and 180 C in the other, so the small package is for a load that is either intermittent or fed from a rail close to the output.

1.5 percent of 3.0 V is 45 mV, and the SOT-23 grade quotes 30 mV instead, so the two order codes are not interchangeable on a rail that is checked against a 3 percent window. The narrow grade is the one to specify when a downstream 3.3 V device has a 3.0 V minimum.

The enable pin has a 500 kOhm pulldown, so it draws 6.6 uA at 3.3 V when driven high and holds the part off when left open. On a board that gates the regulator from a 1.8 V GPIO the pulldown current flows through that GPIO, which is the sort of load a sleep budget forgets.

There is no noise bypass pin, so the only filtering available is the output capacitor and whatever the input provides. A rail that needs low noise at 100 kHz has to get it from the input side or from a different part in the family with an NR pin.

Dropout is specified in output bands, and the 140 mV figure belongs to outputs from 2.5 V to 5.5 V. A 1.2 V output does not get a proportionally smaller drop, it gets the 1.6 V input floor, so a 1.2 V rail from a 1.5 V source cannot be made with this part at any current even though the dropout number looks reassuring.

When the enable goes low the output is discharged through the internal pulldown instead of floating, which is what a sequenced board wants but also makes the disabled state a load: a 10 uF output discharged from 3 V releases 45 uJ, so toggling the enable at 1 kHz dissipates 45 mW in the pulldown and the part is warm with no load connected.

Where this order code fits

Wearables, sensor nodes and camera modules use this part where a 300 mA rail has to fit beside the device it powers and the input is a battery or a 3.3 V bus. A camera module that draws 200 mA in bursts and microamps between frames is the load this body size was chosen for: the 300 mA ceiling keeps the burst inside the rating while the average stays far below it, so the 199.6 C/W of the four ball package never sees a steady state. The four ball package has no exposed pad, so the only path out is the ball array and the copper under it, which is why the SOT-23 version is the one to choose above 100 mA of steady load. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Is 3.0 V from a 3.3 V rail possible at full load? Only if the rail is within about 4 percent. The 140 mV of dropout puts the floor at 3.14 V, and a 3.3 V rail at minus 5 percent is below it.

Does it need an input capacitor? Yes, and it needs to be placed at the IN pin; the part is stable with small ceramic capacitors, but that assumes the capacitor is where the pin is and not at the other end of a trace.

What is the quiescent current? The ground current depends on load and mode and the datasheet quotes it at several output currents, so the number to use is the one at the current the application actually draws, not the headline.

Can the enable pin be tied to the input? Yes. The internal pulldown then carries 6.6 uA continuously at 3.3 V, which is small but is drawn whether or not anything else is awake.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.