Contact Us

TPS7A2018YCKR

Brand: Texas Instruments
Texas Instruments TPS7A2018YCKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A2018YCKR — Power Management & Signal Chain | Superb Automation

TPS7A2018YCKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A2018YCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A2018YCKR: 1.8 V in the 0.616 mm DSBGA body

The TPS7A2018YCKR is the 1.8 V fixed output of the TPS7A20 family in the four bump DSBGA body coded YCK, 0.616 mm by 0.616 mm. On a module, a hearable or a camera flex, the regulator is often the largest remaining component on the board, and this body removes it from the area budget entirely. The electrical figures are those of the family: 300 mA, 7 uV RMS of noise, 95 dB of rejection at 1 kHz and a 1.5 percent maximum tolerance.

The packing is the part that surprises buyers. The vendor lists 12000 pieces on a large tape and reel for this body, so a prototype build either buys a full reel or works from a repacked strip. The bumps are tin silver copper over a gold flash, the moisture level is 1, and the marking is the single character Y, which is all the die size allows.

Key electrical data for the 1.8 V DSBGA point

Input range1.6 V to 6.0 V, 2.0 V minimum for full regulation at 300 mA
Output current300 mA, current limit up to 770 mA in this body, short circuit 160 mA
Quiescent current6.5 uA typical, 10 uA maximum
Accuracyplus or minus 1.5 percent over minus 40 to 125 C
Dropout at 300 mA200 mV in the 1.5 V to 2.5 V band, 690 mV in the 0.8 V to 1.0 V band
Rejection95 dB at 1 kHz into 20 mA, 60 dB at 100 kHz
Thermalthe bumps are the only heat path, so the landing copper is part of the thermal path

Package, marking and reel data

BodyDSBGA YCK, 4 bumps, 0.616 mm by 0.616 mm, 0.35 mm pitch
Reel12000 pieces, large tape and reel, 180 mm carrier, 8 mm tape
FinishSNAGCU
Moisturelevel 1, 260 C peak reflow, unlimited floor life
MarkingY

Where a die scale regulator earns its place

Hearables, smart watches, camera flexes and sensor modules are the obvious homes. In those products the board is often a flex or a rigid flex with a few square millimetres of rigid area, and a regulator in a SOT-23 would take a quarter of it. The DSBGA body also shortens the path from the die to the output capacitor, which helps the rejection at the higher frequencies where the loop is no longer in control.

The catch is mechanical rather than electrical. A 0.35 mm pitch needs a stencil, a placement accuracy and a reflow profile that a prototype line may not have, and the bumps give no compliance against board flex. A product that bends the flex near the regulator will crack the joint, and the fix is a stiffener rather than a different part. The thermal path also depends entirely on the copper under the bumps, so the landing pattern has to follow the reference rather than be reduced for space.

Buyer questions on the DSBGA code

Why is the reel 12000 pieces? That is the only packing the vendor publishes for the YCK body. For a pilot line the practical route is a repacked strip from a distributor, with the date code and the moisture history recorded.

Can a SOT-23 part be fitted in its place? No. The pad patterns are unrelated. A board built for the DSBGA needs a new pad pattern to accept any leaded package, so the choice has to be made before the board is released.

Is the low inrush behaviour different in this body? No. The soft start and the inrush limit belong to the die and are the same across the four bodies. The only differences are the current limit ceiling, which reaches 770 mA here, and the thermal path.

Buying die scale packages

Die scale parts are the ones most likely to be counterfeited when they are short, so the incoming check matters more than the price. Sourcing audit trail describes the documentation we keep for a reel, and kitting covers splitting a 12000 piece reel into the quantity a build actually consumes.

The single character marking is all the die size allows, so lot traceability comes from the reel label rather than from the part, which is one more reason to keep the label with the strip. The current limit ceiling in this body is 770 mA rather than the 730 mA of the X2SON, and the short circuit figure is 160 mA in both. Because the bumps are the only thermal path, the landing copper under the die is part of the thermal specification, and a reduced pad for space invalidates the junction to ambient figure the data sheet quotes. The 12000 piece packing and the single character marking also mean that a repacked strip should travel with its reel label, since the part itself carries no lot information.