Contact Us

TPS7A2018PDBVR

Brand: Texas Instruments
Texas Instruments TPS7A2018PDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A2018PDBVR — Power Management & Signal Chain | Superb Automation

TPS7A2018PDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A2018PDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A2018PDBVR: the 1.8 V, 300 mA low noise point in SOT-23

The TPS7A2018PDBVR is the 1.8 V fixed output of the TPS7A20 family in the SOT-23 body. It is the version most boards specify, because 1.8 V is the standard core and analog voltage for a generation of processors and sensors, and because the SOT-23 footprint is the one an assembly house can place without a special stencil. The electrical behaviour matches the rest of the line: 300 mA, 7 uV RMS of noise, 95 dB at 1 kHz and a 1.5 percent maximum tolerance.

The trim sits in the band where the dropout is 200 mV at 300 mA, so the input floor for full regulation is 2.0 V. That allows the rail to run directly from a 2.5 V or 3.3 V system supply with a linear stage, or from a buck converter set at 2.1 V, which is the arrangement used when the switching residue has to be removed.

Key electrical data for the 1.8 V point

Input range1.6 V to 6.0 V, 2.0 V minimum for full regulation at 300 mA
Output current300 mA, current limit 360 mA to 730 mA, short circuit 160 mA
Quiescent current6.5 uA typical, 10 uA maximum, 0.2 uA in shutdown
Accuracyplus or minus 1.5 percent maximum over the full junction range
Dropout at 300 mA200 mV in the 1.5 V to 2.5 V band, 690 mV in the 0.8 V to 1.0 V band
Rejection95 dB at 1 kHz into 20 mA, 75 dB at 10 kHz, 45 dB at 1 MHz
Noise7 uV RMS over 10 Hz to 100 kHz with a 1 uF ceramic output capacitor

Package, marking and reel data

BodySOT-23 DBV, 5 pins, 2.9 mm by 2.8 mm
Reel3000 pieces, large tape and reel, 180 mm carrier, 8 mm tape
FinishNIPDAU or SN depending on the addendum row
Moisturelevel 1, 260 C peak reflow
Marking2AUF

Where a 1.8 V low noise rail belongs

Camera modules, RF front ends, sensor hubs and audio paths all want this voltage with a quiet supply. The reason an engineer picks a linear stage here rather than a second switching rail is the rejection at 1 kHz to 100 kHz, which is exactly where a buck converter's ripple and its harmonics sit. With 95 dB at 1 kHz and 75 dB at 10 kHz, a 20 mV switching ripple at the input becomes microvolts at the output, which is below the noise floor of the circuits being supplied.

Placement is half the performance. The 1 uF output capacitor has to sit within a couple of millimetres of the pin with a short ground return, and the input capacitor has to be at least as close, because the rejection figure assumes the input is already quiet at the pin. A rail that measures badly on the bench is usually a board with a long ground return rather than a part that fails its specification.

Buyer questions on the 1.8 V SOT-23 code

Can the DSBGA version be substituted if the reel is short? Only with a board change. The YCK and YCJ bodies are about 0.61 mm square with 0.35 mm bumps, and no adapter converts a SOT-23 pad to that pattern reliably. The substitution has to be planned before the board is released.

Is 300 mA the guaranteed output current? Yes, over the full temperature range with the specified capacitors. The current limit window sits above it at 360 mA minimum, which is what allows the load to recover from a transient without the limit engaging.

Does the part have a discharge circuit? No. The output decays through the load when the enable pin goes low. A circuit that needs a defined discharge has to add a resistor or choose a family with the active pulldown.

Buying a 1.8 V low noise part

A 1.8 V analog rail is usually shared by several circuits, so a substitution has to be checked against the whole load rather than one block. OEM procurement describes how we handle a qualified part number with an approved alternate, and the PCBA quote checklist lists the information we need to quote an assembly that includes this rail.

The soft start limits the current drawn from the input at power up, which matters when the rail is fed from a buck converter that is itself starting. The output capacitor has to be 1 uF or more of ceramic and placed within a couple of millimetres of the pin, because the 95 dB rejection figure assumes the input is quiet at the pin and the loop is compensated for that value. Load regulation is quoted with the same 1 uF capacitor, and a board that fits 10 uF improves the transient but changes the loop response, so the two figures should be read as a set rather than independently.