TPS7A20185PDBVR
Product Specifications
TPS7A20185PDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A20185PDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A20185PDBVR: 1.85 V, 300 mA, low noise, in the five pin SOT-23
The TPS7A20185PDBVR is the 1.85 V fixed output of the TPS7A20 family in the SOT-23 body coded DBV. The family is built around three numbers: 7 uV RMS of output noise, 95 dB of rejection at 1 kHz, and a 1.5 percent maximum tolerance over the whole junction range, all from a 1 uF ceramic output capacitor and no bypass pin. At 1.85 V the rail suits an analog domain that needs a little more headroom than 1.8 V without reaching 2.5 V.
Sixty five hundred nanoamps of quiescent current is the compromise the family makes for that noise floor. A nanopower part draws two hundred nanoamps but cannot hold a low noise output, and a low noise part without a quiescent budget would draw tens of microamps. This part sits between the two, which is why it appears in handsets, network cameras and field transmitters that are mains powered but need a quiet rail.
Key electrical data for the 1.85 V point
| Input range | 1.6 V to 6.0 V, 2.15 V minimum for full regulation at 300 mA |
| Output current | 300 mA, current limit 360 mA to 730 mA, short circuit 160 mA |
| Quiescent current | 6.5 uA typical, 10 uA maximum over the full temperature range |
| Accuracy | plus or minus 1.5 percent maximum over minus 40 to 125 C |
| Dropout at 300 mA | 200 mV in the 1.5 V to 2.5 V band, 145 mV in the SOT-23 body at 3.3 V output |
| Rejection | 95 dB at 1 kHz into 20 mA, 92 dB at 300 mA, 60 dB at 100 kHz |
| Noise | 7 uV RMS over 10 Hz to 100 kHz, no bypass capacitor required |
Package, marking and reel data
| Body | SOT-23 DBV, 5 pins, 2.9 mm by 2.8 mm |
| Reel | 3000 pieces, large tape and reel, 180 mm carrier, 8 mm tape |
| Finish | NIPDAU on the plain row, NIPDAU or SN where the addendum lists both |
| Moisture | level 1, 260 C peak reflow, unlimited floor life |
| Marking | 2CBF |
Where a 1.85 V rail belongs
The rail feeds a circuit whose specification is written at about 1.8 V but whose supply tolerance is tight: an image sensor analog supply, a low noise amplifier bias, an audio codec reference or a precision analog to digital converter front end. In those circuits the switching regulator upstream is set a few hundred millivolts higher and this part removes the residue, so the converter can run at a higher frequency and a smaller inductor, which is where the board area saving comes from.
The thermal budget is generous at this voltage. From 3.3 V in to 1.85 V out at 300 mA the part dissipates 435 mW, which the SOT-23 body passes with a reasonable copper pad; from a 5 V rail the same load dissipates 945 mW and the SOT-23 becomes the wrong body, at which point the circuit either moves to a lower input or drops the load current. The 200 mV dropout in the 1.5 V to 2.5 V band means a 2.05 V input still regulates, so a pre regulator set at 2.1 V is enough.
Buyer questions on the 1.85 V code
How is this different from the 1.8 V member of the same family? Only the trim. The die, the noise, the rejection and the bodies are identical, and the two codes are interchangeable on a board as long as the system tolerates either voltage.
Does the part need an output capacitor larger than 1 uF? No. One microfarad of ceramic is the stability condition and the value used for the noise and transient figures. Larger values reduce undershoot further but are not required.
What happens when the enable pin is left floating? An internal pulldown holds the part off, so a missing resistor does not leave the rail enabled. The threshold is 1.0 V high and 0.4 V low, which interfaces directly with 1.2 V logic.
Sourcing this regulator
Low noise regulators are usually bought against a board that has already been qualified, so continuity of supply matters more than price. Safety stock planning sets out how much cover a programme should hold for a single source part, and date code management covers the storage rules for a reel that may sit for a year.
In the SOT-23 body the dropout in the 2.5 V to 5.5 V band is 145 mV, six microvolts of extra drop compared with the smaller bodies, and the 1.5 V to 2.5 V band sits at 200 mV. That is the whole electrical difference between the packings, so a product that needs the lowest dropout should use the X2SON or the DSBGA and a product that needs a leaded part accepts 5 mV more. The current limit is 360 mA minimum, 520 mA typical and 730 mA maximum in this body, and the short circuit figure is 160 mA.