Contact Us

TPS7A1030PDSER

Brand: Texas Instruments
Texas Instruments TPS7A1030PDSER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A1030PDSER — Power Management & Signal Chain | Superb Automation

TPS7A1030PDSER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A1030PDSER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A1030PDSER: a 3.0 V rail with a 0.75 V input floor

The TPS7A1030PDSER is the 3.0 V fixed output of the TPS7A10 line, in the six pin WSON body coded DSE. The output reaches the top of the family range, which runs 0.5 V to 3.0 V in 50 mV steps, and the part still delivers 300 mA from an input as low as 0.75 V because the internal circuits run from the bias pin. At 3.0 V out the input path dropout is 90 mV in this body, so a 3.1 V source holds the rail at full load.

The 3.0 V trim is the one that feeds a sensor analog domain or a low voltage logic rail in a wearable, where the battery cannot supply 3.3 V directly and a boost stage would add switching noise. The same die also ships in the five bump DSBGA body at 0.74 mm by 1.09 mm, which is the version used when the board area is the limiting factor rather than the assembly cost.

Key electrical data for the 3.0 V point

Input range0.75 V to 3.3 V on IN, 1.7 V to 5.5 V on BIAS, bias at least 1.4 V above the output
Output current300 mA, current limit around 600 mA, short circuit 150 mA
Quiescent current1.6 uA on the input pin, 6 uA on the bias pin
Accuracyplus or minus 1.5 percent over load, line and the full junction range
Dropout90 mV maximum at 300 mA in the WSON body, 70 mV in the DSBGA body above 1.0 V output
Rejection60 dB at 1 kHz, with the bias pin rejection quoted separately in the data sheet
Soft startmonotonic output rise, so the rail cannot dip on the way up

Package, marking and reel data

BodyWSON DSE, 6 pins, 1.5 mm by 1.5 mm
Reel3000 pieces, large tape and reel, 180 mm carrier, 8 mm tape
FinishNIPDAUAG
Moisturelevel 1, 260 C peak reflow
MarkingDR

Where a 3.0 V rail belongs in a battery product

The load that fits this part is a sensor hub, a camera module supply or a low power radio that wants 3.0 V while the battery sits between 3.4 V and 3.7 V. A linear stage from the battery would waste 700 mV times the load current; a buck converter would deliver 3.1 V with ripple. This regulator sits after the buck and removes the ripple for a fraction of the loss, and its own quiescent current of 1.6 uA plus 6 uA is small enough that the rail can stay on in standby.

The thermal calculation is the one to do before committing. At 3.1 V in, 3.0 V out and 300 mA the part dissipates 30 mW and the junction rise in a 1.5 mm WSON with a modest pad is a few degrees. At 3.3 V in the figure is 90 mW, which is still comfortable, but a circuit that feeds the input from a 5 V rail instead of from the buck will dissipate 600 mW and exceed the package. The bias pin, by contrast, only carries microamps, so its 0.85 V dropout is a voltage requirement and not a thermal one.

Buyer questions on the 3.0 V WSON code

Does the part work if the bias rail is the same 3.3 V as the system? Yes, provided the bias sits at least 1.4 V above the output at all times. For a 3.0 V output that means a bias of 4.4 V or more, so a 3.3 V system rail is not enough and the battery, or a 5 V rail, has to be used.

What is the maximum output voltage this family reaches? 3.0 V. Anything above that belongs to a different family; the input range of 0.75 V to 3.3 V is the physical limit and it caps the output as well.

Why 2.2 uF on the output rather than 1 uF? The loop is compensated for 2.2 uF and the data sheet stability conditions assume it. A 1 uF capacitor drops the phase margin and shows up as ringing after a load step at light load.

Buying the 3.0 V part

When a wearable programme moves from prototype to production the reel size becomes the constraint, and a 3000 piece reel of a single fab part is the usual weak point. Strategic sourcing sets out how we hold cover across a ramp, and the BOM shortage recovery page covers the short term route when a line stops for one regulator.

The bias rail is the constraint at 3.0 V. It has to sit 1.4 V above the output and inside 1.7 V to 5.5 V, so a 4.4 V or higher source is required, and a 3.3 V system rail will not do. That is why the part appears in battery products where the pack is the only high rail, and why the input can then be the 3.1 V output of a buck converter. The 2.2 uF input and output capacitors and the 0.1 uF bias capacitor are the stability conditions, and the soft start is monotonic so a supervisor sees a clean edge rather than a dip at the start of the ramp.