Contact Us

TPS7A0533PDBVR

Brand: Texas Instruments
Texas Instruments TPS7A0533PDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A0533PDBVR — Power Management & Signal Chain | Superb Automation

TPS7A0533PDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A0533PDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A0533PDBVR: 1.4 V to 5.5 V input 200 mA LDO with 1 microamp quiescent current, 3.3 V fixed

TPS7A0533PDBVR is a fixed 3.3 V linear regulator with a 1 microamp quiescent current, a foldback current limit and a shutdown state that draws almost nothing, built for rails that stay on while the rest of the board sleeps in a SOT-23 (DBV) body of 5 pins. It takes 1.4 V to 5.5 V on the input, holds 3.3 V at up to 200 mA and drops 212 mV typical at full current. Nominal accuracy is plus or minus 1 percent and plus or minus 3 percent over temperature, the ground pin current is 6 microamp at 200 mA, and the part is stable with a 1 microfarad ceramic output capacitor.

Order code and package

Order code read outTPS7A05 33 P DBV R: regulator TPS7A05, 3.3 V fixed output, P version in the five pin SOT-23, R large tape and reel
PackageSOT-23 (DBV), 5 pins, 2.90 mm by 1.60 mm, part marking I6
Carrier in the vendor addendumTPS7A0533PDBVR at 3000 pieces on a large reel; TPS7A0533PDBVT is the same part in a 250 piece small reel; the DBZ three pin body and the X2SON body carry the same die
Moisture levelLevel 1, 260 degrees peak reflow, unlimited floor life
Lead finishNickel palladium gold, quoted as NIPDAU
Temperature rangeJunction minus 40 to plus 125 degrees, storage minus 55 to plus 150
Absolute maximum6 V on the input, 6 V on the enable pin, and an output that may be pulled above the input within the same 6 V limit because the part tolerates a reverse condition rather than conducting through a body diode

Electrical parameters that decide the application

Input range1.4 V to 5.5 V, which is low enough for a 1.8 V rail to feed a 1.2 V rail through this part
Output3.3 V fixed on this order code, from a family that covers 0.8 V to 3.3 V in fixed steps and in adjustable form
Output current200 mA, with a foldback current limit that reduces the current as the output falls rather than holding a constant limit into a short
AccuracyPlus or minus 1 percent at 25 degrees for outputs at or above 1 V, plus or minus 2 percent from minus 40 to plus 85 degrees and plus or minus 3 percent over the full range
Dropout212 mV typical at 200 mA on a 3.3 V output, rising to 275 mV in the 2.5 V to 3.3 V group and higher for lower outputs, all measured to the point where the output falls 5 percent
Quiescent current1 microamp typical and 3 microamp maximum with no load, which is the figure that decides battery life on a rail that is always on
Ground current at load6 microamp typical at 200 mA, so the standing loss barely changes between no load and full load
Shutdown currentThe enable pin pulls the part into a state measured in tens of nanoamps, and the data sheet specifies the maximum rather than leaving it to a typical curve
Start-up1.5 ms typical and 2.8 ms maximum from the enable assertion to 95 percent of the output on a 1.8 V rail
StabilityStable with a 1 microfarad ceramic output capacitor and a 1 microfarad input capacitor, with no ESR requirement beyond what a ceramic part provides
Thermal267.3 degrees per watt junction to ambient for the five pin SOT-23 on a JEDEC board, 144.1 for the X2SON body, so the copper under the part decides the usable current at a high ambient
Reverse behaviourThe part is specified to survive an output held above the input within the 6 V limit, which matters on a bus where another supply can back feed the rail

Bodies and order codes in the same family

TPS7A0533PDBVRthe part on this page, 3.3 V, five pin SOT-23, 3000 pieces on a reel
DBZ three pin bodythe same die without an enable pin, for a rail that is always on and has no need for a shutdown control
X2SON and DSBGA bodiesthe same die in smaller bodies, 144.1 and 198.0 degrees per watt, chosen when board area matters more than thermal headroom
Fixed and adjustable optionsthe family covers fixed outputs from 0.8 V to 3.3 V, so a 1.2 V or 1.8 V rail is a different order code rather than a divider change
P suffixthe version in the five pin body with the enable pin, which is what the R suffix reel on this page carries

Points to check before this part goes on a BOM

A 1 microamp quiescent current is the whole point of this part, and it changes what a standby rail can do. A regulator that draws 50 microamp adds 438 milliamp hours a year, which is a measurable share of a coin cell; at 1 microamp the figure is under 9 milliamp hours a year and the shelf life of the product is set by the load rather than the regulator. The 3 microamp maximum matters as much as the typical, because a board has to be quoted against the worst unit rather than the datasheet headline.

The 1.4 V minimum input is unusually low and it allows a two stage cascade from a single cell. A 1.8 V rail can feed this part to make 1.2 V, and a 3.3 V rail can make 2.5 V, both with dropout to spare. The limit on that is the dropout table: it is 212 mV at 3.3 V out and 200 mA, but 609 mV in the 1.2 V to 1.5 V group, so a low output rail needs more headroom than the headline number suggests.

Foldback current limiting is a quieter behaviour than a constant limit. As the output falls the limit also falls, so a shorted output draws a small fraction of the 200 mA rating instead of holding 200 mA into the short and heating the package until thermal shutdown. The cost is that a load with a large inrush can be starved at start up, so a rail that has to charge a big capacitance should be checked against the foldback curve rather than the nominal current.

The thermal numbers are the reason the five pin SOT-23 is not always the right body. At 267.3 degrees per watt, a 0.5 W dissipation would raise the junction by 134 degrees, which is outside the rating at any normal ambient. In practice the part only dissipates heavily when the input is far above the output, so a 5 V to 3.3 V rail at 200 mA loses 0.34 W and needs the copper to carry it, while a 3.6 V to 3.3 V rail at the same current loses 0.06 W and is comfortable in any body.

One microfarad of ceramic on the output is all the stability requirement asks for, and that is worth quoting because it lets a customer remove an electrolytic from a bill of materials. The same is true on the input, where 1 microfarad is enough, though a longer input trace from the source will want more. The part does not need a feed forward capacitor and has no noise reduction pin, so the external component count is three: two capacitors and the enable pull up.

The reverse condition tolerance is a small feature with a large practical value on a board with several supplies. If a 3.3 V rail is held up by another source after this regulator is disabled, the output sits above the input, and a part without that tolerance will conduct through its body diode and discharge the rail into whatever is left of the input. This one is specified to survive the condition within the 6 V limit, which is why it appears on rails that share a bus with a battery or a second converter.

Where this order code fits

Used on always-on rails in smoke and heat detectors, utility and water meters, wearable and handheld products, and any board where a 200 mA rail has to stay alive for years on a small cell. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

How low can the input go? 1.4 V, so a 1.8 V rail can feed a 1.2 V output through this part. The dropout is what limits the combination: 212 mV at 3.3 V out and 200 mA, but over 600 mV in the 1.2 V to 1.5 V output group.

What is the quiescent current? 1 microamp typical and 3 microamp maximum with no load, and the ground current only rises to 6 microamp at the full 200 mA, so the standing loss is essentially flat across the load range.

Is an external compensation or noise capacitor needed? No. The part is stable with a 1 microfarad ceramic output capacitor and a 1 microfarad input capacitor, and there is no noise reduction or feed forward pin on this device.

What happens on a shorted output? The limit folds back, so the current falls as the output voltage falls instead of holding 200 mA into the short. That protects the package but can starve a load with a very large inrush, so the foldback curve should be checked for those rails.

Which reel does production receive? The R suffix is 3000 pieces on a large reel and the T suffix is 250 pieces on a small reel. The three pin DBZ and the X2SON bodies are separate order codes with the same die.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.