Contact Us

TPS7A0318PDQNR

Brand: Texas Instruments
Texas Instruments TPS7A0318PDQNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A0318PDQNR — Power Management & Signal Chain | Superb Automation

TPS7A0318PDQNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A0318PDQNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A0318PDQNR: the 1.8 V, 200 mA nanopower regulator in the 1 mm X2SON body

The TPS7A0318PDQNR is the 1.8 V fixed output of the TPS7A03 family, a 200 mA linear regulator whose quiescent current is 200 nA typical, or about a fifth of a microamp, and it holds that figure even when the part sits in dropout. For a product that spends most of its life asleep on a coin cell or a lithium thionyl chloride pack, that number decides shelf life far more than the load current does. The 18 in the order code is the trim point in tenths of a volt, so 1.8 V is set at the factory and cannot be moved afterwards.

The family covers 0.8 V to 5.0 V in 50 mV steps, takes 1.5 V to 6.0 V at the input, and is specified over a junction range of minus 40 to plus 125 degrees. The DQN suffix is the four pin X2SON body at 1 mm by 1 mm, and the P before it marks the large tape and reel packing. Two other bodies carry the same die: a four pin DSBGA coded YCH at 0.637 mm square, and a five pin SOT-23 coded DBV.

Key electrical data for the 1.8 V point

Input range1.5 V to 6.0 V, the 1.8 V point needs at least 2.5 V for full regulation at 200 mA
Output current200 mA, current limit window 240 mA to 750 mA, short circuit 65 mA
Quiescent current200 nA typical, 250 nA maximum at 25 C, 220 nA in dropout
Shutdown current3 nA typical, 10 nA maximum with the enable pin at 0 V
Accuracyplus or minus 1 percent at 25 C, 1.5 percent over the full temperature range
Dropout at 200 mA490 mV maximum in the 1.5 V to 1.8 V band, 700 mV over the full range
Noise and rejection130 uV RMS at 0.8 V out over 10 Hz to 100 kHz, 55 dB rejection at 1 kHz

Package, marking and reel data

BodyX2SON DQN, 4 pins, 1.0 mm by 1.0 mm, 0.5 mm pitch
Reel3000 pieces, large tape and reel, 180 mm carrier, 8 mm tape
FinishNIPDAU, with a NIPDAUAG alternate row in the same addendum
Moisturelevel 1, 260 C peak reflow, unlimited floor life
MarkingG3 on the top of the package

Where a 1.8 V nanopower rail belongs

A 1.8 V rail at 200 mA is the supply of a sleeping microcontroller, a gas or water meter front end, a smoke detector, a pulse oximeter or a battery backed real time clock. In each case the load is a few tens of microamps for hours and a burst of a few milliamps when the radio or the sensor wakes. The figures that matter are therefore the quiescent current, the recovery from a load step, and the behaviour when the battery voltage falls to the output level. The family quotes a 1 mA to 50 mA step settling inside 10 microseconds with 80 mV of undershoot, and it keeps its low quiescent current in dropout rather than tripling it the way an adaptive bias regulator does.

The thermal side is rarely the limit here. At 200 mA from 2.5 V into 1.8 V the part dissipates 140 mW, which a 1 mm square body passes to a modest copper area without stress. The number to check first is the dropout window: with 490 mV of maximum dropout at 200 mA, an input below 2.29 V lets the rail follow the battery down. That is acceptable in a meter that only needs 1.8 V for its logic, and it is not acceptable in a circuit whose analog reference assumes a regulated 1.8 V.

Buyer questions on the 1.8 V order code

Is this the same die as the SOT-23 and the DSBGA versions? Yes. The 18 trim, the 200 mA rating and the 200 nA quiescent current are shared across DQN, YCH and DBV. What changes is the body, the reel and the marking, so a purchase order must name the body if the board has only one footprint.

What does the smart enable pin do? It holds the regulator off through an internal 500 kOhm pulldown when the enable pin is left floating, so a product cannot wake up because of a missing resistor. The enable threshold is 1.1 V high and 0.3 V low, which suits 1.8 V logic directly.

Does a 1 uF output capacitor cover the whole family? Yes, 1 uF or larger is the stability condition stated in the data sheet, and the figures quoted for load transient and noise assume that value. Below 1 uF the phase margin is not guaranteed at the cold end.

Buying this rail through a component supplier

These nanopower regulators are ordered in reel quantities and cross referenced against other 200 mA parts when a board is re-spun, so the comparison table on our power management cross reference page lists the pin compatible alternatives by body. When a reel is short and production is waiting, the route through component lead time solutions covers partial reels, date code control and the incoming check on a 3000 piece shipment.

The dynamic behaviour is worth a line of its own, because a nanopower regulator is often chosen on quiescent current and then found wanting on a load step. A 1 mA to 50 mA step settles inside 10 microseconds with 80 mV of undershoot, which is comfortable for a microcontroller wake and marginal for a radio that draws 150 mA for a few hundred microseconds. Load regulation is 20 mV across the 1 mA to 200 mA range up to 85 degrees and 38 mV over the full range, and line regulation is 5 mV across the input window. A circuit that sees a 150 mA burst should add 2.2 uF or more at the output rather than rely on the 1 uF minimum, and it should check that the burst does not sit long enough to heat the four pin body.