Contact Us

TPS7A0233PDQNR

Brand: Texas Instruments
Texas Instruments TPS7A0233PDQNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A0233PDQNR — Power Management & Signal Chain | Superb Automation

TPS7A0233PDQNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A0233PDQNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A0233PDQNR: 200 mA nanopower LDO, 3.3 V fixed, 1 mm by 1 mm X2SON

TPS7A0233PDQNR is a fixed 3.3 V linear regulator rated 200 mA in a one millimetre square body in a X2SON body of 4 pins. It is the same silicon as the SOT-23 member of the family, in a four pin body that measures one millimetre on a side, with 25 nanoamp of quiescent current and 3 nanoamp in shutdown. The four pin body has no enable pin, so the regulator is on whenever the input is present, which is the right arrangement for a sensor node that has nothing else to switch it.

Order code and package

TPS7A0233PDQNRActive, X2SON-4, 3000 pieces on a large reel, minus 40 to 125 degrees
TPS7A0230PDQNRActive, the 3.0 V option in the same body
SOT-23 equivalentTPS7A0233PDBVR, five pins with an enable, 3000 pieces on a large reel
DSBGA optionthe YCH body at 12000 pieces on a reel, the smallest of the three
Column cautionthe addendum prints the package column one row off on this family, read the body from the suffix

Electrical parameters that decide the application

Input voltage1.5 V to 6.0 V
Output3.3 V fixed, 200 mA
Quiescent current25 nanoamp typical, held in dropout
Shutdown current3 nanoamp typical
Dropout270 mV maximum at 200 mA
Accuracy1.5 per cent over temperature
Output capacitor1 microfarad minimum
Pin countfour, input, output, ground and the thermal pad

Family variants and how they differ

DQN body1.0 mm by 1.0 mm, four pins, no enable, this order code
DBV body2.9 mm by 1.6 mm, five pins with enable
YCH body0.64 mm by 0.64 mm DSBGA, the smallest
Close ratiothe pin pitch on the 1 mm body decides the placement tolerance
Thermal padthe exposed pad is the ground connection and the heat path

Points to check before this part goes on a BOM

Four pins means no enable and no bypass. The body has input, output, ground and the pad. A node that has to be switched off needs the five pin SOT-23 member, and the substitution is a board change because the land pattern differs. This is the most common mistake when a board moves from the SOT-23 to the smaller body late in a project.

One millimetre square is a placement decision as much as a part choice. The pin pitch on this body is at the limit of what a standard surface mount line can place, and the solder joint cannot be inspected visually. A board that uses it needs an x-ray step or a very well controlled paste print, which is a cost the part price does not show.

The thermal pad is the ground pin. On a four pin body there is no separate ground, so the pad is both the return and the heat path. A pad that is not properly soldered leaves the regulator without a ground reference, and the failure looks like a dead part rather than a soldering problem.

25 nanoamp holds in dropout because the bias circuit is not referenced to the input. On an ordinary regulator the quiescent current climbs as the input approaches the output, because the bias is taken from the input and the pass device has no headroom. Here the figure is kept, which is what allows a two cell alkaline pack to run the node down to its last few hundred millivolt.

1.5 per cent over temperature is a logic rail figure. For 3.3 V that is about 50 mV across the range. It is fine for a microcontroller, a radio module and a sensor whose output is ratiometric to the same rail. It is not a reference, and a bridge or an ADC that needs an absolute reference needs a different part.

The 3.3 V option is the one with the most stock. The family covers 0.8 V to 5.0 V in 50 mV steps, and the common logic voltages move fastest. A 3.3 V requirement is the easiest to fill, and it is also the one where a substitute from the SOT-23 body is most likely to be available if the small body is short.

A 1 microfarad output capacitor at 200 mA is a small capacitor for the current. The transient response is what makes that possible, with settling under 10 microsecond for a 1 mA to 50 mA step. The capacitor has to be close to the pin, because at this size the trace inductance between the capacitor and the regulator is a significant part of the loop.

Level-1 moisture sensitivity on the 3000 piece reel suits a normal line. No bake and no floor life limit, which matters for a part that is often placed late in the build after the power sections. The handling cost of a level 3 part on a small body would otherwise exceed the price difference.

The smallest body is not always the cheaper answer. A one millimetre part that needs x-ray inspection and a controlled paste print can cost more per board than the SOT-23 member even though the part price is lower. On a low volume board the assembly cost decides, and the larger body wins.

The pad is the electrical ground, so the paste print has to be right. A void under the pad raises the thermal resistance and, on this body, also degrades the ground connection. A part that looks placed and does not regulate is usually a pad problem rather than a silicon problem.

The 3.3 V and 3.0 V options differ only in the internal trim. Same die, same body, same reel, different output. A customer who needs 3.0 V needs a new order code and not a new board, which is worth saying at quotation stage before someone changes a footprint.

One microfarad is a stability value, not a suggestion. The capacitor is part of the loop, and a 100 nanofarad part chosen to save space makes the regulator oscillate. That shows up as noise on the rail rather than as a dead part, which is harder to find.

The regulator is on whenever the input is present. There is no enable pin to switch it off, so the sleep current of the whole node includes the 25 nanoamp of this part plus whatever it supplies. A node that must reach zero current needs a load switch in front.

Where the one millimetre body is worth the assembly cost

Sensor nodes and wearables where the board area is the constraint and the regulator sits next to the sensor it supplies.

Modules potted or encapsulated after assembly, where the part is never inspected again and the small body removes a height problem.

Where this order code fits

It is the same 200 mA nanopower regulator in the 1 mm by 1 mm body, for boards where the SOT-23 footprint does not fit next to the sensor. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Why does this version have four pins? The body is too small for an enable pin. The regulator is on whenever the input is present, so a load that has to be switched needs the five pin SOT-23 member instead.

Is it the same silicon as the SOT-23 part? Yes. The electrical behaviour, the 25 nanoamp quiescent current and the 200 mA rating are the same. The difference is the package, the pin count and the land pattern.

Can it be soldered on a standard line? It can, but the joint cannot be inspected visually at this pitch. A line that places it needs good paste control and usually an x-ray check on the first articles.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.