TPS7A0233DQNR
Product Specifications
TPS7A0233DQNR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A0233DQNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A0233DQNR: 3.3 V at 200 mA in a one millimetre package
The TPS7A0233DQNR is the 3.3 V fixed member of the TPS7A02 family in the four pin X2SON body coded DQN, which measures 1.0 mm by 1.0 mm and is the smallest package in the family. It ships 3000 pieces per reel at moisture level 1 with the marking IF, and it shares the electrical table of the whole family: 200 mA, 25 nanoamps of quiescent current, 1 percent initial accuracy and 1.5 percent over temperature.
This order code and the SOT-23 version carry the same voltage and the same die, so the choice between them is mechanical and thermal rather than electrical. The X2SON is 179.1 C per W and the SOT-23 is 181.9 C per W, a difference of less than 2 percent, so neither body has a thermal advantage. What the small body buys is area, and what it costs is inspectability: the four bumps are under the package and the solder joints cannot be seen after reflow.
Key electrical data for the 3.3 V point
| Output voltage | 3.3 V fixed, plus or minus 1 percent at 25 C and 1.5 percent over -40 to 125 C |
| Output current | 200 mA continuous, current limit 240 mA to 750 mA |
| Input range | 1.5 V to 6.0 V, 3.66 V needed at 200 mA over the full temperature range |
| Quiescent current | 25 nA typical at 25 C, 46 nA maximum, 60 nA maximum to 85 C |
| Dropout | 310 mV maximum at 200 mA to 85 C, 360 mV maximum over the full range |
| Rejection and noise | 55 dB at 1 kHz and 30 mA, 130 uV RMS at 0.8 V over 10 Hz to 100 kHz |
Package, marking and reel data
| Body | X2SON DQN, 4 pins, 1.0 mm by 1.0 mm |
| Reel | 3000 pieces, large tape and reel, 180 mm |
| Finish and moisture | NIPDAU, level 1, unlimited floor life |
| Marking | IF |
| Thermal resistance | 179.1 C per W junction to ambient in the four pin body |
Where the smallest package is the deciding factor
A wearable, a medical patch or a miniature sensor node has an area budget measured in square millimetres. A 1 mm package with a 1 uF capacitor on each side occupies about 3 square millimetres including clearance, against roughly 12 for the SOT-23 version, and on a board with three or four rails that difference is the difference between fitting the enclosure and changing it. The 200 mA rating covers the burst of a radio or a display refresh, and the 25 nA idle current covers the 99 percent of the time when nothing is happening.
The assembly side has to be planned. X2SON packages need a stencil aperture that matches the pad, a placement accuracy better than 50 micrometres and a reflow profile that does not tombstone a part this light. Inspection is by X-ray or by electrical test rather than visually, and rework needs hot air with a nozzle rather than an iron. A buyer who is choosing this body should confirm that the assembly house has run it before, because the part is not the difficulty.
Electrically the rail behaves like the rest of the family: 55 dB of rejection at 1 kHz, 130 microvolts of noise at 0.8 V, a 65 mA short circuit limit and a 10 microsecond settling time for a 1 mA to 50 mA step. The start up time for outputs above 3.0 V is 1200 to 1600 microseconds, the longest band in the family, which is worth knowing when a sequencer enables three rails in order.
Buyer questions on this order code
Can this package be reworked by hand? Not with an iron. The four bumps are under the body, so rework needs hot air with a nozzle and a stencil for the paste, and the part is usually replaced rather than reused.
Does the 200 mA rating hold in this body? The current rating is the same as the other bodies because the die is the same. What changes is the copper area needed to reach the quoted thermal resistance, and the 179.1 C per W figure assumes a pad with a via array.
Is the marking enough to identify the part? It is IF for this voltage and body, which is two characters. Incoming inspection has to compare the reel label and the certificate of conformance, since the marking alone is shared by other members of the family.
Sourcing the TPS7A0233DQNR through SUPERB
SUPERB supplies this order code with the reel label and the certificate of conformance as the identification, because a two character marking cannot be verified on its own. The parts are moisture level 1, so no baking is needed before reflow.
Where the assembly house has not run an X2SON before, the incoming inspection plan page sets out what we check on receipt, and PCBA quote checklist covers the assembly questions to settle before the first build. Send the quantity and the board and the answer follows.