TPS7A0231PDQNR
Product Specifications
TPS7A0231PDQNR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A0231PDQNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A0231PDQNR: 3.1 V at 200 mA from a 25 nA regulator
The TPS7A0231PDQNR is the 3.1 V fixed member of the TPS7A02 family from Texas Instruments, a 200 mA nanopower regulator in the four pin X2SON body coded DQN at 1.0 mm by 1.0 mm. It ships 3000 pieces per reel at moisture level 1 with the marking GJ, and it holds the output inside 1 percent at 25 degrees and 1.5 percent over the full temperature range while drawing 25 nanoamps at no load.
3.1 V is not a common rail value, which is why this order code is usually specified for a reason rather than by default. It appears where a system has to stay inside a 3.3 V absolute maximum with margin for a 5 percent bus, or where a radio or a sensor was characterised at 3.1 V and a 3.3 V rail would push it over a limit. The part sits in the 2.5 V to 3.3 V dropout band, 310 mV maximum to 85 degrees and 360 mV maximum over the full range at 200 mA, so a 3.3 V input leaves 200 mV and is inside the maximum only at light load.
Key electrical data for the 3.1 V point
| Output voltage | 3.1 V fixed, plus or minus 1 percent at 25 C and 1.5 percent over -40 to 125 C |
| Output current | 200 mA continuous, current limit 240 mA to 750 mA |
| Input range | 1.5 V to 6.0 V, 3.46 V needed at 200 mA over the full temperature range |
| Quiescent current | 25 nA typical at 25 C, 46 nA maximum, 60 nA maximum to 85 C |
| Dropout | 310 mV maximum at 200 mA to 85 C, 360 mV maximum over the full range |
| Rejection and noise | 55 dB at 1 kHz and 30 mA, 130 uV RMS at 0.8 V over 10 Hz to 100 kHz |
Package, marking and reel data
| Body | X2SON DQN, 4 pins, 1.0 mm by 1.0 mm |
| Reel | 3000 pieces, large tape and reel, 180 mm |
| Finish and moisture | NIPDAU or NIPDAUAG, level 1, unlimited floor life |
| Marking | GJ |
| Thermal resistance | 179.1 C per W junction to ambient in the four pin body |
Where a 3.1 V nanopower rail fits
The rail is normally a sensor or radio supply in a battery instrument: a thermostat, a smoke or heat detector, a gas or water meter, a glucose monitor or a security sensor. In every one of those the load is a few milliamps for a few milliseconds and microamps the rest of the time, so the regulator's idle current sets the battery life. At 25 nA the part is below the leakage of the output capacitor, which is the point at which the quiescent current stops being a engineering constraint and becomes a rounding error.
The other property worth quoting is the behaviour in dropout. The ground current stays at 25 nA typical even when the input falls to 95 percent of the output, so a battery that sags below 3.1 V does not turn the regulator into a load. That is what allows a product to keep running, with the rail following a falling cell, until the microcontroller browns out on its own threshold rather than on the regulator's.
Thermally the body is small and the rail is close to the input, which is the good case. At 200 mA from 3.6 V to 3.1 V the dissipation is 0.1 W and the rise is 18 degrees. From 5 V the same current is 0.38 W and a 68 degree rise, which is still inside the rating but leaves less room in a sealed enclosure. The load regulation adds to the error budget: 38 mV maximum from 1 mA to 200 mA up to 85 degrees is 1.2 percent of 3.1 V, which is comparable with the accuracy window itself.
Buyer questions on this order code
Why 3.1 V rather than 3.3 V? Because the load is limited to 3.3 V absolute maximum or was characterised at 3.1 V. The two order codes are otherwise the same part in the same body, so the choice is a system decision and the price and the lead time are the same.
What input does 200 mA need? 3.46 V over the full temperature range, because the dropout is 360 mV maximum in this band. At 25 degrees and a lighter load the figure is closer to 310 mV, so a 3.6 V or 4.2 V bus is comfortable.
Does the part need an output capacitor? Yes, 1 uF minimum effective capacitance for stability, and the family is specified with 1 uF input and output. The capacitor has to keep its value at 3.1 V, which a 6.3 V X5R in an 0603 does.
Sourcing the TPS7A0231PDQNR through SUPERB
SUPERB quotes this order code against the 3.1 V trim in the DQN body, and states the marking and the moisture class in the offer because the family shares one body across a dozen voltage points. The GJ marking and the reel label are checked on receipt before the parts enter stock.
Where the 3.1 V point is only needed for a prototype, the kitting service page covers small quantity builds, and component shortage forecast covers a line that moves slowly. Send the quantity and the annual usage and the quote follows.