TPS7A0210PDQNR
Product Specifications
TPS7A0210PDQNR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A0210PDQNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A0210PDQNR: 1.0 V at 200 mA from a 25 nA quiescent regulator
The TPS7A0210PDQNR is the 1.0 V fixed member of the TPS7A02 family from Texas Instruments, a 200 mA regulator whose quiescent current is 25 nanoamps, which is roughly four hundred times lower than a conventional low dropout part and low enough that a battery powered product can leave the rail enabled for years. It comes in the four pin X2SON body coded DQN at 1.0 mm by 1.0 mm, 3000 pieces per reel, marking GH, moisture level 1.
The 1.0 V point has two properties that separate it from the higher voltages in the same family. Its accuracy is specified in millivolts rather than in percent, 15 mV at 25 degrees and 20 mV over temperature, because a percentage window on a 1 V rail would be tighter than the trim step. And its dropout is the largest in the family: 790 mV maximum up to 85 C and 850 mV maximum over the full range at 200 mA, against 310 mV and 360 mV at 3.3 V. A 1.0 V rail therefore needs 1.85 V of input at full load, and the 1.5 V input floor only applies at light load.
Key electrical data for the 1.0 V point
| Output voltage | 1.0 V fixed, plus or minus 15 mV at 25 C and 20 mV over -40 to 125 C |
| Output current | 200 mA continuous, current limit 240 mA to 750 mA |
| Input range | 1.5 V to 6.0 V, 1.85 V needed at 200 mA because of dropout |
| Quiescent current | 25 nA typical at 25 C, 46 nA maximum, 60 nA maximum to 85 C |
| Dropout | 790 mV maximum at 200 mA up to 85 C and 850 mV maximum over the full range |
| Rejection and noise | 55 dB at 1 kHz and 30 mA, 130 uV RMS at 0.8 V over 10 Hz to 100 kHz |
Package, marking and reel data
| Body | X2SON DQN, 4 pins, 1.0 mm by 1.0 mm |
| Reel | 3000 pieces, large tape and reel |
| Finish and moisture | NIPDAU, level 1, unlimited floor life |
| Marking | GH |
| Thermal resistance | 179.1 C per W junction to ambient in the four pin body |
Where a 1.0 V nanopower rail is the right answer
A 1.0 V rail at 200 mA is a modern core voltage: a microcontroller in its low power domain, a sensor hub, a memory rail or a radio baseband. The reason to use this family is not the 200 mA, it is the 25 nA. A wearable, a heat or smoke detector, a gas or water meter, a glucose monitor or a security sensor spends most of its life drawing microamps, and a regulator that burns 1 uA of quiescent current would dominate the budget. At 25 nA the regulator is below the leakage of the capacitor next to it.
The part keeps that quiescent current even in dropout, which is the unusual claim. Most regulators let the ground current rise as the pass device saturates, so a battery that falls below the regulation point drains faster at exactly the moment the product is trying to run on the last of its charge. The 25 nA dropout figure removes that behaviour, which is why the family is written for meters and detectors that have to keep working down to a nearly empty cell.
The load regulation row is where a 1.0 V rail has to be checked carefully. The specification is 20 mV typical and 38 mV maximum from 1 mA to 200 mA up to 85 degrees, and 50 mV maximum to 125 degrees. On a 1.0 V rail 38 mV is 3.8 percent, which is wider than the 1.5 percent accuracy claim, so a load that steps over the full current range sees a window set by the load regulation rather than by the initial accuracy. A converter or a core that needs tighter than that needs a different part or a remote sense.
Buyer questions on this order code
Is the quiescent current really nanoamps at 200 mA of load? The 25 nA figure is at no load and it is the ground current of the regulator itself. At load the ground current rises with the ratio in the table, 0.15 percent of the load above 100 mA, so 200 mA of load adds about 300 uA of ground current. The 25 nA matters in the idle state, not at full load.
What input does a 1.0 V rail need? 1.85 V at 200 mA, because the dropout is 850 mV maximum over temperature. At 1 mA of load the dropout is far lower and the 1.5 V input floor governs instead.
Does the enable pin need a pull down? No. The part has a smart enable pulldown of 500 kOhm that keeps it off when the pin floats, and a 60 Ohm pulldown that discharges the output when the device is disabled. That removes the external resistor normally needed on a floating enable.
Sourcing the TPS7A0210PDQNR through SUPERB
SUPERB quotes this order code against the 1.0 V trim and the DQN body, and states the package in the offer because the same voltage is available in a SOT-23 body in the same family with a different thermal resistance. The GH marking and the level 1 moisture class are verified on receipt.
Where the rail is part of a metering or medical programme, the medical device components page covers the grade and traceability questions, and component lead time solutions deals with the schedule. Send the load profile and the sleep budget and the quote follows.