TPS79925YZUR
Product Specifications
TPS79925YZUR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS79925YZUR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS79925YZUR: 2.5 V, 200 mA, in a five pin wafer level package
The TPS79925YZUR is the 2.5 V fixed member of the TPS799 family from Texas Instruments, a 200 mA regulator in the five pin DSBGA body coded YZU, which measures about 1.5 mm by 1.0 mm and carries the die directly. It ships 3000 pieces per reel with a tin silver copper finish, moisture level 1, marking EC, and it holds the output inside 1 percent at 25 degrees and 2 percent over the full input, load and temperature range.
The package is the reason to choose this order code and also the reason to check it twice. A wafer level package removes the lead frame, so the thermal path runs through the solder balls and the board copper rather than through a tab, and the junction to ambient resistance is 143.3 C per W against 74.2 for the WSON body of the same die. On a small board with little copper the difference is the whole thermal margin at 200 mA.
Key electrical data for the 2.5 V point
| Output voltage | 2.5 V fixed, plus or minus 1 percent at 25 C and 2 percent over the full range |
| Output current | 200 mA continuous, current limit 220 mA to 600 mA |
| Input range | 2.7 V to 6.5 V, 300 mV of headroom at the floor |
| Quiescent current | 40 uA typical and 60 uA maximum from 500 uA to 200 mA |
| Noise | 26.3 uV RMS at 2.5 V with a 0.01 uF capacitor, 235 uV RMS with no capacitor |
| Rejection | 70 dB at 100 Hz, 66 dB at 1 kHz, 51 dB at 10 kHz, 38 dB at 100 kHz |
Package, marking and reel data
| Body | DSBGA YZU, 5 balls, about 1.5 mm by 1.0 mm |
| Reel | 3000 pieces, large tape and reel |
| Finish and moisture | SNAGCU, level 1, unlimited floor life |
| Marking | EC |
| Thermal resistance | 143.3 C per W junction to ambient in the five ball body |
Where a 2.5 V rail in a chip scale package fits
This order code exists for boards where the rail is needed but the area is not available. A 2.5 V supply at 200 mA for a sensor front end, an audio amplifier or a low power radio can sit in 1.5 square millimetres, which on a wearable or a handheld instrument is often the difference between fitting the rail and dropping it. The penalty is thermal and mechanical: the body has to be placed on a copper area that can spread the heat, and the solder joints have to be inspected by X-ray or by the assembly house process control rather than visually.
Electrically the part behaves like the rest of the family. Forty microamps of quiescent current, 70 dB of rejection at 100 Hz and 51 dB at 10 kHz, and a noise floor of 26.3 microvolts at 2.5 V once the noise reduction capacitor is in place. The 2.7 V input floor leaves only 200 mV of headroom for a 2.5 V rail, which is enough at 200 mA but leaves almost nothing for a bus with tolerance, so the input has to be a regulated 2.8 V or above rather than a battery that falls to 2.5 V.
Dissipation at 200 mA is modest at this voltage: from 3.3 V the part absorbs 0.16 W, which on 143.3 C per W is a 23 degree rise. From 5 V it absorbs 0.5 W and rises 72 degrees, which is where the small body stops being an advantage and a WSON part of the same die becomes the better answer.
Buyer questions on this order code
Is the marking just two characters? Yes, EC on the five ball body. The full order code does not fit on a die this size, so incoming inspection has to compare the reel label and the certificate rather than the marking alone.
Can this body be used in a reflow profile for lead free solder? Yes, the finish is tin silver copper and the part is moisture level 1, so it is handled as a standard lead free component. The constraint is board level: the balls are small and the placement accuracy matters more than the profile.
What is the difference against the WSON version? The same die in a different body. The WSON is 74.2 C per W and the DSBGA is 143.3, so the WSON carries roughly twice the dissipation at the same junction temperature. The electrical table is otherwise the same.
Sourcing the TPS79925YZUR through SUPERB
SUPERB supplies this order code with the body and the marking stated, and inspects the reel label against the offer because a two character marking cannot be verified on its own. Moisture level 1 means no baking is needed, and the certificate of conformance carries the finish.
For a rail that has to move to a larger body for thermal reasons, the pin to pin cross reference page lists what changes, and one stop BOM sourcing covers the rest of the bill. Send the area budget and the dissipation and the answer follows.