TPS79733DCKR
Product Specifications
TPS79733DCKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS79733DCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS79733DCKR: 3.3 V, 50 mA, with an open drain power good flag
The TPS79733DCKR is the 3.3 V member of the commercial TPS797 line from Texas Instruments, a 50 mA regulator in the five pin SC70 body coded DCK with an integrated open drain power good output. It ships 3000 pieces per reel at moisture level 1 with the marking ATF, and it is specified over an ambient range of -40 to 85 degrees, which is the commercial grade of the family rather than the automotive one.
The family is unusual in a useful way: the power good flag is active high, which means the open drain output goes to the input rail when the output is in regulation and pulls low when it is not. Most supervisors work the other way round, so a board that expects an active low reset has to invert the signal. The flag trips at about 90 percent of the output voltage and is guaranteed valid from a 1.2 V input, and it can sink 100 uA at 0.4 V.
Key electrical data for the 3.3 V point
| Output voltage | 3.3 V fixed, plus or minus 4 percent over a 1 mA to 10 mA load |
| Output current | 50 mA continuous, current limit 190 mA to 300 mA |
| Input range | 1.8 V to 5.5 V at 3 mA, 2.0 V to 5.5 V at 10 mA |
| Quiescent current | 1.2 uA typical and 2 uA maximum at 10 mA |
| Dropout | 105 mV typical and 200 mV maximum at 10 mA |
| Power good | active high open drain, trip at 90 percent of the output, 0.14 V low at 30 uA |
Package, marking and reel data
| Body | SC70 DCK, 5 pins, 2.0 mm by 1.25 mm |
| Reel | 3000 pieces, large tape and reel |
| Finish and moisture | NIPDAU or NIPDAUAG depending on the row, level 1, unlimited floor life |
| Marking | ATF |
| Thermal resistance | 230.9 C per W junction to ambient in the five pin body |
Where a 3.3 V rail with a flag belongs
The TPS797 line is written for battery equipment that has to stay alive: meters, thermostats, smoke and heat detectors, portable instruments and card readers. A 3.3 V rail at 50 mA covers a microcontroller in a low power mode, a radio in receive, or a sensor front end, and the 1.2 uA quiescent current is what makes a 10 year shelf life arithmetic work. The power good flag adds a supply monitor without a second part, which on a two layer board in a small enclosure is worth more than the flag itself costs.
At 50 mA the thermal picture is still gentle. From 5 V to 3.3 V the part dissipates 85 mW, which on a 230.9 C per W body is a 20 degree rise, so the 85 degree ambient rating is comfortable rather than tight. The limit comes from the load, not from the package: a 3.3 V rail that has to deliver 100 mA belongs to a different family, and the current limit of 190 to 300 mA is a fault protection number rather than a usable operating point.
The accuracy row deserves a note. The plus or minus 4 percent window is specified over a 1 mA to 10 mA load, and the line regulation is 0.15 percent per volt, so a 5 V input gives a slightly higher output than a 3.3 V input. On a 3.3 V rail that feeds a radio, the 4 percent window is wider than the radio likes, and a buyer should check the receiver tolerance before treating this part as a reference supply.
Buyer questions on this order code
Is the power good output active high or low? Active high. The output is an open drain that goes high when the rail is in regulation and pulls low when it is not, which is the opposite of most reset supervisors. A board expecting active low needs an inverter or a different part.
Does the flag need a pull up resistor? Yes, it is an open drain output, so a pull up to the logic rail is required. The flag can sink 30 uA at 0.14 V and 100 uA at 0.4 V, so the resistor has to be sized for the logic threshold rather than for speed.
What current can this part really deliver? 50 mA continuous, with the accuracy specified between 1 mA and 10 mA. The current limit at 190 to 300 mA is fault protection, not a load rating, and the dropout figure is quoted at 10 mA.
Sourcing the TPS79733DCKR through SUPERB
SUPERB quotes this order code against the commercial temperature grade, which is -40 to 85 degrees, and states it in the offer because the automotive members of the same family share the body and the marking style but not the rating. The ATF marking and the level 1 moisture class are verified on receipt.
Where the rail has to be monitored without a second supervisor, the power management cross reference page lists the parts that carry a flag, and safety stock planning covers how we hold a buffer on a part that only moves in small quantities. Send the quantity and the annual forecast and the quote follows.