TPS79730QDCKRQ1
Product Specifications
TPS79730QDCKRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS79730QDCKRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS79730QDCKRQ1: 3.0 V, 10 mA, with a power good flag
The TPS79730QDCKRQ1 is the automotive 3.0 V member of the TPS797 line from Texas Instruments, a very small linear regulator in the five pin SC70 body coded DCK with an open drain power good output. It ships 3000 pieces per reel at moisture level 1 with the marking QTE, and it is specified over an ambient range of -40 to 125 degrees, which is wider than the commercial members of the same family.
The most important number on this page is the output current: 10 mA. The commercial TPS797 members are rated at 50 mA, but the automotive version is specified from 10 uA to 10 mA, and a buyer who treats the two as interchangeable will overload the part. The 10 mA rating comes with a correspondingly tight thermal picture: the DCK body is 396 C per W on a low conductivity board and 315 C per W on a high conductivity one, so even 10 mA from 5 V to 3.0 V is 20 mW and a 6 to 8 degree rise, which is why the part can be rated to 125 degrees at all.
Key electrical data for the 3.0 V automotive point
| Output voltage | 3.0 V, 2.880 V to 3.12 V over -40 to 125 degrees, plus or minus 4 percent |
| Output current | 10 uA to 10 mA, current limit 190 mA to 300 mA |
| Input range | 1.8 V to 5.5 V at 3 mA, 2.0 V to 5.5 V at 10 mA |
| Quiescent current | 1.2 uA typical at 25 C, 5 uA maximum over the full range |
| Dropout | 110 mV typical at 10 mA and 25 C, 400 mV maximum over temperature |
| Power good | trip at 82 to 96 percent of the output, 1.2 V minimum input for a valid flag |
Package, marking and reel data
| Body | SC70 DCK, 5 pins, 2.0 mm by 1.25 mm |
| Reel | 3000 pieces, large tape and reel |
| Finish and moisture | NIPDAUAG, level 1, unlimited floor life |
| Marking | QTE |
| Thermal resistance | 396 C per W on a low conductivity board, 315 C per W on a high conductivity board |
Where a 10 mA automotive rail with a flag is used
This class of part lives in the always on corner of a vehicle module: a keep alive rail for a CAN transceiver, a supply for a sensor that has to stay biased while the module sleeps, a reference for a comparator that watches a battery line. The 1.2 uA quiescent current is the whole point, because a 10 uA budget for an always on rail leaves no room for a general purpose regulator, and the 5 nA shutdown current lets the module hold the rail off for months without touching the battery.
The power good output is what makes the part useful in a safety context. It is an open drain flag that pulls low when the output falls below about 90 percent of nominal, with a 82 to 96 percent band over temperature, and it is valid from a 1.2 V input. That flag can drive a microcontroller reset input or a fault line without an external supervisor, which removes a part and a few square millimetres from a module that has neither to spare.
The limit is the load. At 10 mA the part covers a transceiver, a sensor bias or a reference, and nothing else. A module that needs 30 mA on the keep alive rail needs a different device, and the honest comparison is against the commercial TPS797 members at 50 mA, which do not carry the automotive temperature range or the Q1 documentation.
Buyer questions on this order code
Is 10 mA really the maximum? Yes for the Q1 members. The electrical table specifies the continuous output current as 0 to 10 mA, and the accuracy row is written for a 10 uA to 10 mA load. The commercial TPS797 parts are specified to 50 mA and are not a substitute in an automotive record.
What does the power good flag do at low input? Below 1.2 V of input the flag is not guaranteed valid, so a module that has to report a fault during a cold crank has to hold the input above that floor or ignore the flag in that window.
Why is the thermal resistance so high? The SC70 body has almost no copper area of its own. 396 C per W on a low conductivity board is the honest figure, and it is the reason the current rating is 10 mA rather than 50 mA in this temperature range.
Sourcing the TPS79730QDCKRQ1 through SUPERB
SUPERB quotes the Q1 string with the automotive temperature range and the moisture class stated, because the commercial members of the same family share the body and the marking style. The QTE marking is verified on receipt, and the certificate of conformance carries the temperature grade.
For modules that need a keep alive rail with a flag and a wider current, the power management cross reference page lists the parts we can compare on quiescent current and flag behaviour, and medical device components covers the grade questions for instrumentation programmes. Send the load and the sleep budget and the answer follows.