TPS79601DRBR
Product Specifications
TPS79601DRBR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS79601DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS79601DRBR: adjustable 1.2 V to 5.5 V, 1 A, in an eight pin SON
The TPS79601DRBR is the adjustable member of the TPS796 family from Texas Instruments, a 1 A low noise regulator with a 1.225 V reference, an input range that reaches 6.0 V on the current silicon, and 41 microvolts RMS of noise on the legacy silicon with a 0.01 uF capacitor. It comes in the eight pin SON body coded DRB, 3000 pieces per reel, nickel palladium gold finish, moisture level 2 with a one year floor life, marking CES.
The family document carries both silicon generations and the electrical tables print them side by side. The differences are large enough to matter in a budget: quiescent current runs 265 uA typical on the legacy silicon and 700 uA on the current one, the current limit falls from 2.4 A to 4.2 A on the legacy part to 1.04 A to 1.65 A on the current part, and the accuracy window widens from plus or minus 2 percent to plus or minus 2.5 percent. A board qualified on one generation does not automatically meet the other.
Key electrical data for the adjustable 1 A member
| Output voltage | 1.225 V to 5.5 V minus dropout, set by an external divider |
| Reference | 1.225 V typical, 1.2 V to 1.25 V window, feedback pin current 1 uA |
| Output current | 1 A continuous, current limit 2.4 A to 4.2 A on the legacy silicon |
| Dropout | 270 mV typical and 365 mV maximum at 1 A for the 2.8 V point, DRB body at 250 mA is 52 mV |
| Quiescent current | 265 uA typical and 385 uA maximum on the legacy silicon, 700 and 1100 on the current one |
| Rejection and noise | 54 dB at 100 Hz and 1 A, 53 dB at 10 kHz, 42 dB at 100 kHz, 41 uV RMS with 0.01 uF |
Package, marking and reel data
| Body | SON DRB, 8 pins, exposed pad, 3.0 mm by 3.0 mm |
| Reel | 3000 pieces, large tape and reel |
| Finish and moisture | NIPDAU, level 2, 260 C, one year floor life |
| Marking | CES |
| Thermal resistance | 47.8 C per W on the legacy silicon, 54.7 C per W on the current silicon |
Where a 1 A low noise rail is used
A 1 A linear regulator is a different animal from a 100 mA one. It is used where the load is a whole analog or radio subsection rather than a single reference, which means a transceiver chain, a data converter bank, a phased array front end or an instrument that has to run its analog side from a quiet rail at real current. The rejection figures tell the story: 74 dB at 100 Hz and 1 A on the current silicon, 49 dB at 10 kHz, 42 dB at 100 kHz, so a switching stage in front of it is cleaned up across the whole band the analog load cares about.
The thermal path decides the application. At 47.8 C per W, 1 A from 3.3 V to 1.8 V is 1.5 W and a 72 degree rise, which the eight pin SON can carry on a real copper pad. The same current from 5 V to 1.8 V is 3.2 W and a 153 degree rise, which no linear regulator in this body survives. The honest rule is that this part belongs behind a switching pre regulator, and the switching frequency of that pre regulator is what the rejection numbers are aimed at.
The adjustable version adds the divider and the feed forward capacitor to the fixed members of the family. The feedback pin draws 1 uA, so a 10 kOhm divider burns 122 uA and a 100 kOhm one burns 12 uA, and the choice trades quiescent current against noise pickup at the feedback node. On a 1 A rail the divider current is not the dominant term, so the lower value is usually the better choice.
Buyer questions on this order code
Why is the current limit so different between generations? The legacy silicon limits at 2.4 A to 4.2 A and the current silicon at 1.04 A to 1.65 A. The lower window protects a 1 A load without letting a short circuit pull several amps through the pass device, and it is the row to use when the board has to survive a fault.
Does the DRB body need a thermal pad? Yes. The 47.8 C per W figure assumes the exposed pad is soldered to a copper area with vias to an inner plane. Without that the junction to ambient resistance rises to the point where 1 A is no longer available at any useful ambient.
Can this part take a 6 V input? Only the current silicon, which is rated to 6.0 V. The legacy silicon stops at 5.5 V. The quotation states which generation is being supplied, because the difference decides whether a 6 V bus is inside the rating.
Sourcing the TPS79601DRBR through SUPERB
SUPERB supplies this order code with the silicon generation named in the offer, since the current limit and the input ceiling differ between them. The DRB body, the CES marking and the level 2 moisture bag are verified on receipt, and the date code and certificate of conformance travel with every reel.
For a 1 A analog rail the choice of pre regulator matters as much as the linear part, and the power management cross reference page lists the switching parts we can pair with it. Where the rail has to be built from a fixed voltage member instead, one stop BOM sourcing covers the whole bill. Send the rail, the load and the input bus and the quote follows.