TPS79225DBVR
Product Specifications
TPS79225DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS79225DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS79225DBVR: 2.5 V, 100 mA, low noise in a five pin SOT-23
The TPS79225DBVR is the fixed 2.5 V member of the TPS792 family from Texas Instruments. It delivers 100 mA from an input between 2.7 V and 5.5 V, holds the output inside a 2.45 V to 2.55 V window, and reaches 31 microvolt RMS of noise with a 0.01 uF capacitor on the noise reduction pin. The package is the five pin SOT-23 coded DBV, 3000 pieces per reel, marking PEXI, moisture level 1.
The published dropout number for this member carries a footnote that buyers rarely read: the TPS79225 dropout is limited by the minimum input voltage of 2.7 V rather than by the pass device, so the 2.5 V rail needs only 200 mV of headroom and the regulator can hold it from a 3.0 V bus down to the input floor. That is the reason this voltage point is popular in battery equipment, where a 3.0 V to 3.3 V rail has to survive until the cell is nearly empty.
Key electrical data for the 2.5 V point
| Output voltage | 2.5 V fixed, 2.45 V to 2.55 V window over the load range |
| Output current | 100 mA, current limit 285 mA to 600 mA on the legacy silicon |
| Input range | 2.7 V to 5.5 V, dropout limited by the input floor |
| Quiescent current | 170 uA typical and 250 uA maximum on the legacy silicon |
| Noise | 31 uV RMS with a 0.01 uF noise reduction capacitor, 27 uV with 0.1 uF |
| Rejection | 70 dB at 100 Hz and 100 mA, 75 dB at 10 kHz, 47 dB at 100 kHz on the legacy silicon |
Package, marking and reel data
| Body | SOT-23 DBV, 5 pins, 2.90 mm by 1.60 mm, noise reduction pin on pin 4 |
| Reel | 3000 pieces, large tape and reel |
| Finish and moisture | NIPDAU, level 1, unlimited floor life |
| Marking | PEXI |
| Thermal resistance | 225.1 C per W on the legacy silicon, 171.7 C per W on the current silicon |
Where a 2.5 V, 100 mA rail fits
2.5 V is the supply of a large part of the analog world: reference buffers, low noise amplifiers, ADC drivers and sensor front ends that were written around a 2.5 V full scale. It is also the rail that has to be clean, because a 2.5 V reference chain sets the accuracy of everything behind it. Twenty seven microvolts of noise with a 0.1 uF capacitor is low enough that the regulator contributes less than one bit of a 16 bit converter over a 100 kHz band, and 75 dB of rejection at 10 kHz removes the switching residue of a 500 kHz converter sitting on the same input.
The current budget is modest, so the choice of capacitor matters more than the choice of package. The family is stable with a 1 uF ceramic on the output, but the noise reduction pin needs its own capacitor to ground, and that capacitor also sets the start up ramp. With 0.01 uF the start up is around 70 microseconds, and removing the capacitor does not break stability but it does raise the noise by roughly a factor of two.
On the thermal side, 100 mA from 5 V to 2.5 V is 0.25 W, which on a 225 C per W body is a 56 degree rise. That is acceptable on a board with copper under the pins but it is the reason the 5 V to 2.5 V case is usually fed from a pre regulator rather than straight from a 5 V bus in a sealed enclosure.
Buyer questions on this order code
Is the five pin body the same as the adjustable one? No. The five pin body is fixed voltage and carries a noise reduction pin on pin 4 instead of a feedback pin. The adjustable member uses the six pin body. The outlines are close enough to confuse a pick and place file, so the pin function table is the check.
What is the difference against the 2.8 V member? Only the trim point and the input floor. Both share the electrical table apart from the output window, so the 2.8 V member needs 3.0 V of input for the same 200 mV of headroom. A substitution between them changes the analog full scale, which is not a component decision alone.
Does the part need a minimum load? No. The family is specified from 0 A to 100 mA and holds regulation with no load. The quiescent current is the only current drawn at zero load and it stays at 170 uA typical.
Sourcing the TPS79225DBVR through SUPERB
SUPERB stocks and quotes this order code with the body, the marking and the moisture class confirmed on the reel label, because a five pin SOT-23 with a noise reduction pin is easy to confuse with the fixed members of other families that share the outline. Parts arrive with the date code and a certificate of conformance, and the incoming inspection covers marking, packaging and pin one orientation.
If the 2.5 V rail is being reworked, the power management cross reference page lists the parts that can serve the same point, and how to reduce component cost sets out where a second source is worth the qualification effort. Send the rail and the load and the answer comes back with the options ranked.