Contact Us

TPS78550QWDRBRQ1

Brand: Texas Instruments
Texas Instruments TPS78550QWDRBRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS78550QWDRBRQ1 — Power Management & Signal Chain | Superb Automation

TPS78550QWDRBRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS78550QWDRBRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS78550QWDRBRQ1: the 5.0 V, 1 A member of the TPS785-Q1 family

The TPS78550QWDRBRQ1 is the fixed 5.0 V, 1 A output of the TPS785-Q1 line from Texas Instruments. Its input window runs from 1.7 V to 6.0 V, its initial accuracy is plus or minus 0.5 percent at 25 degrees, and its junction rating reaches 150 degrees rather than the 125 degrees used on most general purpose linear regulators. The Q1 letter marks the automotive qualification and the digits 550 in the order code mark the 5.0 V trim point, so the rail value is fixed at purchase and cannot be moved afterwards.

The family is built in two bodies, an eight pin VSON coded DRB and a five pin TO-252 coded KVU, and the letters before the package code tell a buyer which one is in the box. On this page the body is the DRB, 3000 pieces on a 330 mm reel, nickel palladium gold finish, moisture level 2 with a one year floor life once the seal is broken. The same 5.0 V point in the KVU body ships 2500 pieces at moisture level 3 with a 168 hour floor life, which is a real difference on the reflow line and the reason the two order codes are not interchangeable in production planning.

Key electrical data for the 5.0 V point

Output voltage5.0 V fixed, the fixed family runs 0.65 V to 5.0 V
Output current1 A continuous, current limit 1.04 A to 1.65 A, short circuit 550 mA
Input range1.7 V to 6.0 V, the 5.0 V point needs at least 5.315 V for full regulation
Accuracyplus or minus 0.5 percent at 25 C, 1 percent to 85 C, 1.7 percent to 150 C
Dropout at 1 A315 mV in the 3.3 V to 5.5 V band, DRB body, measured at 95 percent of nominal
Quiescent current15 uA typical at no load, 33 uA maximum at 25 C, 40 uA maximum to 150 C

Package, marking and reel data

BodyVSON DRB, 8 pins, exposed thermal pad, 3.3 mm by 3.3 mm
Reel3000 pieces, large tape and reel, 330 mm, 12 mm tape
Finish and moistureNIPDAU, level 2, 260 C, one year floor life
Marking8550QW on every reel
Thermal resistance59.5 C per W junction to ambient in the DRB body

Where a 5.0 V, 1 A linear rail belongs

A 5.0 V rail at 1 A sits in an awkward place. From a 5.5 V bus the headroom is 500 mV and the dropout over the full band is 315 mV at 1 A, so the rail holds at nominal load but loses regulation once the bus sags by more than about 185 mV. From a 12 V or 24 V bus the regulator has to absorb 7 W or 19 W, which no eight pin body can pass to the board, so the honest use of this part is a post regulator behind a switching stage that already sits near 5.5 V, or a 5.0 V rail drawn from a well held 5.5 V to 6.0 V source such as a protected battery pack.

Inside automotive and industrial equipment the part usually carries the analog and interface side of the board: sensor bias, CAN transceiver supply, op amp rails and reference chains where a switching ripple is not acceptable. The rejection figures support that role. At 1 A the family holds 60 dB at 1 kHz, 45 dB at 100 kHz and 30 dB at 1 MHz, so a 400 kHz switching stage in front of it is attenuated by roughly 40 dB and the residual ripple at the analog rail falls into the microvolt range. Where the load is a 5.0 V logic rail with 1 A of transient step, the load transient table is the number to read: a 300 mA to 700 mA step settles in 10 microseconds and the deviation stays within 2 percent of the output, while a full 0 to 1 A step reaches 10 percent of the output for the duration of the recovery.

The thermal side decides whether the part is usable at all. At 59.5 C per W, 1 A from 5.5 V to 5.0 V dissipates 0.5 W and lifts the junction by 30 degrees above board temperature, which is comfortable. The same current from a 6.0 V input lifts it by 59.5 degrees and the 150 degree rating becomes the limit rather than the ambient. The exposed pad has to be soldered to a copper area with vias, otherwise the junction to ambient figure is meaningless.

Buyer questions on this order code

What separates this from a TPS78550QKVURQ1? The die is the same and the 5.0 V trim is the same. The difference is the body, the reel size, the finish and the moisture level: DRB gives 3000 pieces at level 2 with a one year floor life, KVU gives 2500 pieces at level 3 with a 168 hour floor life and a 425 mV dropout in the wide band instead of 315 mV.

Is the 150 degree junction rating a marketing number? The electrical table is specified to 150 degrees for accuracy, dropout and quiescent current, so the numbers hold at that junction temperature. The 150 degree row of the accuracy table is 1.7 percent, not 1 percent, which is the figure to carry into a worst case budget.

Does the part need an output capacitor? Yes. The data sheet specifies 1 uF input and output as the test condition and the family is stable from 1 uF upward. The capacitor has to keep its value at the rail voltage, so a 1 uF 6.3 V X5R in an 0603 is a safer choice than a 1 uF 50 V part whose derated value collapses under bias.

Sourcing this rail through SUPERB

SUPERB supports the TPS785-Q1 body as a line item rather than a catalogue page. We hold the DRB and KVU order codes against real reel quantities, confirm the date code and the moisture bag on receipt, and quote the rail with the certificate of conformance attached. For programmes that need a second source or a pin compatible alternative when the 5.0 V point moves, the power management cross reference page lists the parts we can compare against this one.

Send the BOM line, the annual quantity and the target price and the quote comes back with the reel size and the lead time stated. If the 5.0 V rail is not fixed yet, say which load and which headroom the rail has to survive and we will answer with the order codes that fit the arithmetic: power management cross reference, and for schedule pressure component lead time solutions.