TPS78430QDBVRQ1
Product Specifications
TPS78430QDBVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS78430QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS78430QDBVRQ1 automotive 3.0 V 300 mA regulator in SOT-23
The TPS78430QDBVRQ1 is the 3.0 V fixed member of the TPS784-Q1 family in the five pin SOT-23 body, ordered on a 3000 piece reel. It sources 300 mA from an input between 1.65 V and 6.0 V with 0.5 per cent typical and 1.7 per cent maximum accuracy, 25 microamp of quiescent current and 50 dB of rejection out to 100 kHz. The 3.0 V point is the one that suits a 3.3 V bus with a margin left for the transceiver, or a sensor that wants a rail below the logic supply to keep its input range inside the amplifier's window.
The internal soft start of 500 microseconds and the active output discharge make the part easy to sequence in a module that has several rails: the enable pin starts a controlled ramp, and pulling it low discharges the output rather than leaving it floating. Foldback current limit keeps the dissipation down during a short, and thermal shutdown at 150 degrees junction protects the die. The body is the same five pin SOT-23 as the rest of the family, so one land pattern covers every fixed point.
Key parameters printed in the SBVS387C document
| Output | 3.0 V fixed, with 0.65 V to 5.0 V members in the family |
| Input range | 1.65 V to 6.0 V |
| Load current | 300 mA |
| Accuracy | 0.5 per cent typical, 1.7 per cent maximum over the operating range |
| Quiescent current | 25 microamp typical |
| Rejection and soft start | 50 dB out to 100 kHz, internal soft start of 500 microseconds |
| Protection | Foldback current limit, thermal shutdown, active output discharge on disable |
| Thermal | Minus 40 to plus 150 degrees junction, dissipation limited by the copper under the body |
Package, reel and top side marking
| Package | SOT-23, DBV body, five pins |
| Reel | 3000 pieces on a large tape and reel |
| Finish and moisture | Nickel palladium gold, moisture level 1, unlimited floor life |
| Temperature and marking | Minus 40 to plus 150 degrees junction, top side marking per the addendum row |
Where a 3.0 V fixed rail earns its place
From a 5 V bus into 3.0 V at 300 mA the part drops 600 mW, which the five pin body holds with a copper pour and does not hold on a narrow trace. That arithmetic is what makes the 3.0 V member the one that most often sits directly on a 5 V input, because the dropout is small enough that the heat is manageable and no intermediate rail is needed. The rail then feeds a CAN transceiver, an op amp pair or a memory device, each of which wants a supply that does not move when the 5 V bus sags.
The value of the fixed member here is repeatability across builds. A 3.0 V rail that is set by a divider is a rail whose set point is one resistor tolerance away from the transceiver's minimum, and the difference between 3.0 V and 3.15 V is the difference between a bus that works at the corner and one that does not. With the divider inside the package the set point is the same on every board. Where a program needs several voltage points, the pin to pin cross reference page lists the family members that share the footprint so the bill of materials can hold one body and several codes.
Questions buyers ask before ordering
Can it drop 5 V to 3.0 V at 300 mA? Yes, at 600 mW of dissipation. The five pin body holds that with a copper area, and the junction temperature is the number to check rather than the current rating.
Does the enable pin tolerate 5 V? The enable is rated for the input range of the part. Driving it from a 5 V logic rail is inside the specification, and a series resistor is not required for level shifting.
Why choose 3.0 V over 3.3 V? The 3.0 V point leaves the transceiver's minimum with margin when the bus sags, and it keeps a sensor's input range inside the amplifier window on a 3.3 V logic supply, which is the case on a bridge sensor whose common mode sits at half of the excitation.
Ordering this part through SUPERB
SUPERB supplies this regulator against a bill of materials line, confirms the fixed point from the code and keeps the reel label with the certificate. A 3.0 V rail also leaves a transceiver more room than a 3.3 V rail when the bus is loaded at the far end, because the driver is specified against the supply it actually sees. Send the rail, the load and the bus voltage through the incoming inspection plan page when the part has to be checked against a drawing at goods in, and the answer comes back with the code and the reel that matches.