TPS78412QDBVRQ1
Product Specifications
TPS78412QDBVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS78412QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS78412QDBVRQ1 automotive 1.2 V 300 mA regulator in SOT-23
The TPS78412QDBVRQ1 is the 1.2 V fixed member of the TPS784-Q1 family in the five pin SOT-23 body, ordered on a 3000 piece reel. It is the same die as the adjustable member with the divider inside the package, which removes two parts from the board and the divider tolerance from the error budget: the accuracy stays at 0.5 per cent typical and 1.7 per cent maximum over minus 40 to plus 150 degrees junction. Quiescent current is 25 microamp typical and rejection is 50 dB out to 100 kHz.
At 1.2 V the headroom question becomes the first question. The input floor is 1.65 V, so the part can regulate a 1.2 V rail from a 1.65 V supply with 450 mV to spare, and the dropout of 115 mV maximum on the 3.3 V member is not the binding constraint at this voltage; the input floor is. That is what makes the family useful on a 1.8 V intermediate bus, where a 1.2 V core rail has to be derived without a switcher and without losing the last few hundred millivolts.
Key parameters printed in the SBVS387C document
| Output | 1.2 V fixed, with 0.65 V to 5.0 V members in the family |
| Input range | 1.65 V to 6.0 V, which is the binding constraint at this output |
| Load current | 300 mA |
| Accuracy | 0.5 per cent typical, 1.7 per cent maximum over the operating range |
| Quiescent current | 25 microamp typical |
| Rejection and soft start | 50 dB out to 100 kHz, internal soft start of 500 microseconds |
| Protection | Foldback current limit, thermal shutdown, active output discharge on disable |
| Thermal | Minus 40 to plus 150 degrees junction, dissipation limited by the copper area under the five pin body |
Package, reel and top side marking
| Package | SOT-23, DBV body, five pins |
| Reel | 3000 pieces on a large tape and reel |
| Finish and moisture | Nickel palladium gold, moisture level 1, unlimited floor life |
| Temperature and marking | Minus 40 to plus 150 degrees junction, top side marking 23KF |
Where a fixed 1.2 V member is the safer choice
A 1.2 V rail is a core rail, and a core rail that is fed from a linear regulator is fed from an intermediate bus that is already close to it. The usual arrangement is a switcher down to 1.8 V and this part from 1.8 V to 1.2 V, which drops 600 mV at 300 mA and dissipates 180 mW, a figure the five pin body holds without a thermal pad. Attempting the same from 3.3 V is 630 mW and still inside the package with a copper pour, but from 5 V it is 1.14 W and the copper becomes the limit.
The fixed member also removes a failure mode that shows up in production: a divider with one wrong resistor that passes at room temperature and fails at the temperature extreme because the reference drifts against the divider. With the divider inside the package the set point is one number in one record. Where the same board also needs a 1.8 V or a 3.3 V point, the family covers them with the same footprint, and the pin to pin cross reference page lists the members that drop into the same land pattern.
Questions buyers ask before ordering
Can it run from a 1.5 V input? No. The input floor is 1.65 V, so a 1.5 V bus is below the operating range of this family regardless of the dropout figure.
Why does the fixed version cost less board area? The divider is inside the package, so two resistors and their tolerance are removed. That is the whole difference from the adjustable member in the same body.
Is the 1.7 per cent maximum over temperature? Yes, it is specified over the operating range from minus 40 to plus 150 degrees junction, not at 25 degrees only.
Ordering this part through SUPERB
SUPERB supplies this regulator against a bill of materials line and confirms the fixed voltage point from the code, because the family shares one document and the codes differ in the middle digits. The second reason to hold the fixed member is a qualification file that already names a set point: a new divider means a new measurement and a new signature, while a fixed member keeps the same record with a different code. Where the intermediate bus is a switcher, the switching frequency and the rejection at that frequency are the pair to check, because 50 dB at 100 kHz is not 50 dB at 2 MHz. Send the rail, the load and the intermediate bus through the one stop BOM sourcing page and the answer comes back with the code, the reel and the date code. A rail that is specified at 1.2 V plus or minus 2 per cent cannot absorb a second divider tolerance on top of the device band.