TPS78326DDCR
Product Specifications
TPS78326DDCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS78326DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS78326DDCR 2.6 V regulator with 500 nA of quiescent current
The TPS78326DDCR is the 2.6 V member of the TPS783 family in the five pin SOT-5 body, rated at 150 mA with a quiescent current of 500 nA. It is the same idea as the low current families beside it taken one step further: the reference and the error amplifier are biased at a current small enough that the regulator disappears from the standby budget of a battery powered product. Output is stable with a 1 microfarad ceramic capacitor, dropout is 130 mV at 150 mA at room temperature and 175 mV at 85 degrees, and the accuracy is 3 per cent over load, line and temperature.
One property of this family is easy to miss and useful. The output has no pulldown circuitry, so when the input collapses the output capacitor can hold the rail for a short time instead of being discharged through the die. In a product that swaps a battery while the load is a sleepy microcontroller, that capacitor becomes a temporary backup supply, and the rail stays up long enough for the controller to finish writing to non volatile memory. Shutdown current at the ground pin is 18 nA typical, and the enable pin draws 0.07 microamp, so a driven enable costs nothing in the budget.
Key parameters printed in the SBVS133A document
| Input range | 2.2 V to 5.5 V |
| Output | 2.6 V fixed for this code, with other fixed points in the family |
| Load current | 150 mA |
| Quiescent current | 500 nA typical, 8 microamp at 150 mA |
| Dropout | 130 mV at 150 mA at 25 degrees, 175 mV at 150 mA at 85 degrees |
| Accuracy | 3 per cent over load, line and temperature |
| Current limit | 150 mA to 400 mA |
| Shutdown and enable | 18 nA typical at the ground pin with the enable low, 0.07 microamp enable current |
Package, reel and top side marking
| Package | SOT-5, DDC body, 2.9 mm by 1.6 mm |
| Reel | 3000 pieces on a large tape and reel, 250 pieces on a small reel for the T row |
| Finish and moisture | Nickel palladium gold, moisture level 2, one year floor life |
| Temperature and marking | Minus 40 to plus 105 degrees junction, top side marking SIB |
Where 500 nA decides the product
This is the regulator for a coin cell or a lithium primary cell that has to last the shelf life of the product plus a decade of service. At 500 nA the regulator itself is a rounding error against the leakage of the microcontroller it feeds, which is the point at which the rail stops being the constraint and the load becomes the thing to fix. The 2.6 V point matches a two cell alkaline pack at end of life, and the 150 mA rating covers the wake up surge of a radio without ever being reached in continuous operation.
The temperature range is the one restriction worth writing down: this family is specified to 105 degrees junction, not 125, so it belongs in a handheld or a battery powered sensor and not next to a power stage. A product that needs the same current at 125 degrees takes the automotive family beside it and pays for it in idle current. The second point is the missing output pulldown, which is a feature in a battery swap and a hazard in a redundant supply, where two regulators on one rail will fight over the output capacitor unless a diode or a load switch separates them.
Questions buyers ask before ordering
Can two of these share a rail? Not directly. With no output pulldown, both regulators hold the rail and the higher set point wins; a diode or a load switch per source is the usual arrangement.
Is 500 nA the whole board current? No, it is the regulator. The board figure includes the load in its sleep state and any divider left on the enable pin, and that is the number to measure.
Why is the maximum junction temperature 105 degrees? It is the qualification of this family. A product that sees a higher ambient needs the automotive family, which is specified to 150 degrees junction.
Ordering this part through SUPERB
SUPERB supplies this part against a bill of materials line and confirms the voltage point and the reel from the code, because the family shares one document and the fixed points differ only in the last digits. A product that ships for fifteen years will need more than one reel of this part, and the second supply has to match the first in idle current rather than only in voltage, because the standby budget written into the specification is the one the certification was granted against. Past that point the last time buy and LTB planning question becomes the cheaper one to answer early. Send the rail, the cell and the annual quantity through the safety stock planning page and the answer comes back with the reel size and the date code on the stock.