Contact Us

TPS78227QDRVRQ1

Brand: Texas Instruments
Texas Instruments TPS78227QDRVRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS78227QDRVRQ1 — Power Management & Signal Chain | Superb Automation

TPS78227QDRVRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS78227QDRVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS78227QDRVRQ1 automotive 2.7 V regulator with 1 microamp of idle current

The TPS78227QDRVRQ1 is the 2.7 V member of the TPS782-Q1 family in the six pin 2 mm by 2 mm SON body, rated at 150 mA with a quiescent current of 1 microamp. That figure is the whole point of the part: an always on rail that feeds a real time clock, a memory card detector or a smoke detector has to survive years on a small cell, and at 1 microamp the regulator itself stops being the dominant term in the budget. The family is qualified for automotive applications and is specified over minus 40 to plus 125 degrees junction.

Dropout is 130 mV at 150 mA at room temperature and 175 mV at 85 degrees, which is honest about the temperature coefficient rather than quoting the room figure alone. Current limit is 150 mA to 400 mA, so the part can charge its own output capacitor and still fold back before the die is stressed, and shutdown current is 18 nA typical, which is what makes a battery powered product's shelf life believable. The output is stable with a 1 microfarad ceramic capacitor, so the whole rail is two small parts.

Key parameters printed in the SBVS138 document

Output2.7 V fixed, with 2.5 V, 2.7 V, 2.8 V and 3.0 V members in the family
Load current150 mA
Quiescent current1 microamp typical, 1.4 microamp maximum at no load, 8 microamp at 150 mA
Dropout130 mV at 150 mA at 25 degrees, 175 mV at 150 mA at 85 degrees
Accuracy4 per cent over load, line and temperature
Current limit150 mA to 400 mA
Shutdown current18 nA typical at the ground pin with the enable low
Noise and stability86 microvolt RMS over 100 Hz to 100 kHz, stable with a 1 microfarad ceramic output capacitor

Package, reel and top side marking

PackageSON, DRV body, six pins, 2 mm by 2 mm
Reel3000 pieces on a reel
Finish and moistureNickel palladium gold, moisture level 1 on the reel row
Temperature and markingMinus 40 to plus 125 degrees junction, top side marking OFH

Where 1 microamp changes the product

The 2.7 V point is the one that matches a lithium primary cell at end of life, so this member is usually the always on supply in a metering or sensing product that has to run for a decade. The 150 mA rating is not the operating current of that rail, it is the surge when a radio or a card reader wakes; the idle figure is what the cell sees for the other 99.9 per cent of the time. Where the same product is built in an automotive variant, the Q1 record covers the temperature and the qualification, and the medical device components page covers the same family when the end product is an instrument rather than a vehicle module.

Two measurements matter before this part is written into a bill of materials. The first is the enable leakage, because a 1 microamp regulator behind an enable divider that draws 5 microamp is a divider problem, and the fix is a higher value or a driven enable. The second is the dropout at end of life, 130 mV at room temperature and 175 mV at 85 degrees, which sets the cut off voltage the controller software has to use; a 2.7 V rail from a 3.0 V cell has 300 mV of headroom when the cell is new and almost none when it is flat, so the product needs to know which side of that line it is on.

Questions buyers ask before ordering

Is 1 microamp achievable on a real board? The regulator itself draws 1 microamp typical. The board total depends on the parts it feeds and on any divider left connected to the enable pin, so the measurement is made at the cell, not at the regulator.

Does it need a minimum load? No. The part regulates from no load, which is the case it was built for, and the 1.4 microamp maximum applies at exactly that point.

Why is the accuracy 4 per cent? The reference is trimmed for low current rather than for precision, so the band is wider than a general purpose regulator. A rail that needs 1 per cent accuracy should not use this family.

Ordering this part through SUPERB

SUPERB supplies this part against a bill of materials line, confirms the output voltage point from the code rather than the family name, and keeps the reel label with the certificate. Send the rail, the cell chemistry and the target date through the date code management page and the answer comes back with the reel size and the date code on the parts in stock.