Contact Us

TPS75100DSKR

Brand: Texas Instruments
Texas Instruments TPS75100DSKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS75100DSKR — Power Management & Signal Chain | Superb Automation

TPS75100DSKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS75100DSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS75100DSKR two bank LED driver with PWM brightness control

The TPS75100DSKR is a linear current source for keypad and indicator backlighting, not a voltage regulator. It drives up to four LEDs at 25 mA each in two banks of two, in a common cathode arrangement, with independent enable and brightness control per bank. The default current is set in the factory between 3 mA and 10 mA in 1 mA steps and stored in EEPROM, so the usual external ballast resistor disappears along with its tolerance. An external resistor can still be fitted to move the initial brightness, but the factory value is accurate to 0.5 per cent typical and needs no parts.

Brightness is controlled by a PWM signal on the enable pin of each bank, so a dimming ratio comes from the duty cycle rather than from a current DAC. There is no internal switching regulator and no charge pump, which means no switching edge to filter and no radiated emission from the driver itself; the part drops the difference between the battery and the LED string as heat, which is why the 28 mV dropout figure matters on a single cell supply. Ten pin SON body, minus 40 to plus 85 degrees, and a top side marking of SKX.

Key parameters printed in the SBVS080J document

Output current25 mA per LED, four LEDs, two banks of two, common cathode
Current matching2 per cent LED to LED, 0.5 per cent typical on the factory set value
Dropout28 mV typical, which keeps the banks in regulation near the end of a single cell discharge
Default currentFactory set from 3 mA to 10 mA in 1 mA steps through EEPROM
Brightness controlPWM on the enable pin of each bank, independent per bank
SupplySingle cell Li-Ion and 3.3 V or 5 V rails, no inductor and no flying capacitor
ProtectionThermal shutdown and current limit on each bank
EmissionNo internal switching signal, so the driver adds no switching harmonic to the supply

Package, reel and top side marking

PackageSON, DSK body, ten pins, 3 mm by 3 mm
Reel3000 pieces on a large tape and reel, 250 piece small reel on the T suffix
Finish and moistureNickel palladium gold, moisture level 1, unlimited floor life
Temperature and markingMinus 40 to plus 85 degrees, top side marking SKX

Where this driver fits

The part suits a front panel with two illumination zones that have to be dimmed separately, typically a keypad and a status strip. Because matching is 2 per cent between LEDs and the two banks share one die, a panel that used to bin LEDs by forward voltage can stop doing it: the current source absorbs the spread. The limit is headroom. With 28 mV of dropout the driver needs only a little more than the LED string voltage, but on a 3.3 V rail with two white LEDs in series the sum is already near the rail, so the bank count per string is the first decision, not the current setting.

Heat is the second decision. Dropping 5 V to a 3.2 V string at 50 mA per bank is under 100 mW per bank, which the ten pin body handles without a thermal pad. Attempting the same with four LEDs in series from a 12 V rail is a different problem and belongs in a switching driver. Where a panel has to be re-lit after a long production run, the factory set current can be re-programmed rather than changed on the board, which keeps the bill of materials identical between the two builds; the pin to pin cross reference page lists the variants of the same body with different default currents so a substitution does not need a new land pattern.

Questions buyers ask before ordering

Is the default current fixed at purchase? It is programmed in EEPROM before the part ships. The 25 mA per LED ceiling is the silicon limit, the default is the number written at the factory, so the order code has to carry it.

Can the two banks run at different currents? Yes. Each bank has its own enable pin and its own PWM duty cycle, so brightness is set per bank even though the default current is shared.

Does it need an output capacitor? No. The part is a current source with no control loop that needs compensation, and the document shows the application circuit without one.

Ordering this part through SUPERB

SUPERB supplies this driver against a panel bill of materials and confirms the default current with the factory value written on the reel label, because two order codes that differ only in the EEPROM byte look identical on the outside. Send the string arrangement, the bank count and the target current through the medical device components page if the panel is part of an instrument, and the answer comes back with the order code that carries the right default.