TPS74601PQWDRBRQ1
Product Specifications
TPS74601PQWDRBRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS74601PQWDRBRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS74601PQWDRBRQ1 1 A automotive adjustable regulator
The TPS74601PQWDRBRQ1 is the adjustable member of the TPS746-Q1 family, a 1 A low dropout regulator in the eight pin VSON body with wettable flanks, on a 3000 piece reel. The 01 in the code is the adjustable output, P is the active output discharge, the blank power good position is the open drain output with a 150 microsecond delay, Q is the AEC-Q100 grade 1 marking, W is the wettable flank body, DRB is the eight pin package and R is the 3000 piece reel.
It is the same body and the same pinout as the 500 mA member, with a larger pass device and a lower feedback reference point that lets it regulate down to 0.55 V. The gain in current comes with a cost in dropout at the low end, and the family table prints both so the choice is a calculation rather than a guess.
Key parameters from the SBVS358D document
| Input range | 1.5 V to 6.0 V |
| Output range | 0.55 V to 5.5 V adjustable, fixed members from 0.65 V to 5.0 V |
| Current | 1 A continuous, current limit 1.22 A minimum, 1.5 A typical and 1.83 A maximum |
| Short circuit current | 500 to 850 mA with 680 mA typical, foldback behaviour |
| Accuracy | Plus or minus 0.85 percent typical at 25 degrees and plus or minus 1.5 percent maximum over temperature |
| Dropout | 265 mV maximum at 1 A in the 1.8 to 2.5 V band, 160 mV maximum in the 3.3 to 5.5 V band |
| Quiescent current | 25 microamp typical, 1.5 microamp in shutdown |
| Rejection | 53 dB at 1 kHz, 38 dB at 100 kHz and 30 dB at 1 MHz at 1 A of load |
| Noise | 53 microvolt RMS over 10 Hz to 100 kHz at 0.9 V out |
| Undervoltage lockout | 1.21 to 1.47 V rising and 1.17 to 1.42 V falling, so it works below the 1.5 V operating floor on the way down |
| Thermal resistance | 55.5 degrees per watt junction to ambient in the eight pin VSON body |
| Order code | TPS74601PQWDRBRQ1, 3000 pieces on a large reel, nickel palladium gold finish, level 2, one year floor life |
One amp in a 3 mm body is a thermal promise, not an electrical one
The 1 A rating is honest at the die and the body limits it. At 1 A and 1.5 V out from a 3.3 V input the part burns 1.8 W, which with 55.5 degrees per watt is a 100 degree rise and a junction of 185 degrees at 85 degrees ambient, well past the 150 degree rating. At 500 mA the same rail burns 0.9 W and the rise is 50 degrees, which holds. At 3.3 V out from 5 V and 1 A it burns 1.7 W and the same limit applies.
So the realistic operating window for this part is 500 to 700 mA from a moderate input, or 1 A where the input to output difference is small. A customer who needs 1 A at 1.2 V from a 1.8 V rail is exactly the application the part was built for: 0.6 W, a 33 degree rise, comfortable. A customer who needs 1 A at 1.2 V from 5 V needs a converter, and that conversation is better had before the quote than after the first articles fail.
The adjustable divider has a floor of its own
The feedback voltage on this family is 0.55 V, which is low enough that the divider current is a real part of the budget. A divider of 100 k and 82 k from a 1.2 V output draws about 6.6 microamp, which is acceptable against a 25 microamp quiescent current and doubles the standby draw of the rail. Larger resistors reduce that and make the feedback node more sensitive to leakage, so the document gives a recommended range and the divider should stay inside it.
The 0.55 V reference also means that an adjustable member set to a very low output has less loop gain than the fixed members, and the load transient response at 0.6 V is not the same as at 3.3 V. The typical characteristic curves in the document show that, and a rail that is specified at the bottom of the range should be checked against them rather than against the headline accuracy.
Where this part fits
Cluster displays, cameras, head units, telematics units and short range radar modules use this family, and the 1 A member is the one that appears when a module needs a processor core rail inside the module rather than from the main supply. The cross reference notes are under power management cross reference, and the receipt plan we run on automotive reels is in incoming inspection plan.
Before a purchase order, and the questions that come up
Run the dissipation for the actual input and load, as above, before anything else. The second check is the divider, because the adjustable member needs two resistors that the fixed member does not, and those two parts are a tolerance and a placement the board has to carry.
Is this a drop in for the fixed 1.8 V member? The footprint is the same, the pins are the same and the divider is the difference. Electrically it can be set to 1.8 V, so it is a practical substitution when the fixed code is short.
What is the power good behaviour when the output is below its set point at start up? The output is open drain and stays low until the feedback pin crosses its threshold, and the 150 microsecond delay then applies. The signal is usable as a reset release for a processor without an external supervisor.
Does the part need a bias supply like the larger families? No. The main input alone runs from 1.5 V, and the bias pin arrangement of the TPS742 family is not present here.