TPS73401DRVR
Product Specifications
TPS73401DRVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS73401DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS73401DRVR: 250 mA low noise linear regulator with 60 dB rejection at 1 kHz
TPS73401DRVR is a low noise positive linear regulator for analog rails, adjustable from 1.25 V to 6.2 V with a 125 mV dropout at full current in a WSON body of 6 pins. The TPS73401 is the adjustable member of a family of low noise linear regulators that deliver up to 250 mA with a dropout of 125 mV typical at that current. Noise is 28 uV root mean square, ripple rejection is 60 dB at 1 kHz, and the output is adjustable from 1.25 V to 6.2 V with an external divider. The part is stable with ceramic output capacitors, works from an input of 2.7 V or the output plus 0.3 V, whichever is greater, and comes in a small six pin body.
Order code and package
| Order code | TPS73401DRVR |
| Input voltage | 2.7 V minimum, or the output plus 0.3 V |
| Output current | 250 mA |
| Output voltage | adjustable 1.25 V to 6.2 V |
| Dropout | 125 mV typical at 250 mA |
| Noise | 28 uV root mean square |
| Ripple rejection | 60 dB at 1 kHz |
| Output capacitor | ceramic, stable across the range |
| Package | 6 pin WSON, 1.5 mm by 1.5 mm class body |
| Noise reduction pin | a capacitor on NR lowers the noise further |
| Enable | logic level input with a low current shutdown state |
| Document | TPS734xx family data sheet |
Electrical parameters that decide the application
| Junction range | -40 C to 125 C |
| Reference | 1.25 V nominal, set by the internal bandgap |
| Accuracy | quoted across line, load and temperature in the electrical table |
| Dropout condition | measured at 250 mA with the output 0.5 V below nominal |
| Quiescent current | in the tens of microamps, specified in the electrical table |
| Line rejection band | 60 dB at 1 kHz, falling at higher frequency |
| Soft start | the noise reduction capacitor also slows the ramp |
| Package options | SOT23-5 and the six pin body for the family |
| Thermal path | the die pad on the small body |
| Protection | current limit and thermal shutdown |
| Adjustable divider | two resistors from the output to the feedback pin |
| Load transient | checked against the output capacitor in the electrical table |
Points to check before this part goes on a BOM
The difference between this family and a general purpose regulator is noise and rejection, and both are measured at specific conditions. Sixty decibels at 1 kHz means a 100 mV ripple at that frequency arrives as 100 uV, which is comparable to the regulator noise itself. Above 1 kHz the rejection falls, so a switching converter at 500 kHz is attenuated by a much smaller factor and the input filter has to do the rest.
Twenty eight microvolts of noise is quoted with the noise reduction capacitor fitted. Without that capacitor the noise is higher, and the difference is large enough to matter in a 16 bit measurement chain. A board that leaves the pin open because the capacitor looked optional is not getting the number on the front page.
Dropout of 125 mV at 250 mA is what allows a 3.3 V rail to be produced from a 3.6 V input with margin for the tolerance. At 250 mA and a 1 V drop the dissipation is 250 mW, which a small body can pass to the board, but at a 5 V input and a 1.25 V output the dissipation is 940 mW and the package cannot carry it. The input voltage is therefore part of the thermal decision, not just a headroom question.
Stability with ceramic capacitors is not the same as stability with any capacitor. The equivalent series resistance of the output capacitor is part of the loop, and a board that replaces a ceramic with a tantalum of the same value can see a response that rings. The document specifies the capacitor range that was verified, and staying inside it is cheaper than measuring a new loop.
Adjustable output from 1.25 V means a divider that draws current from the output at all times. For a 3.3 V output with a 1 kOhm bottom resistor the divider draws 1.25 mA, which is small against a 250 mA load but significant on a rail that spends most of its life at a few milliamps. Larger resistors reduce the drain and increase the noise pickup on the feedback pin, so the divider is a real trade.
The noise reduction capacitor also sets the soft start. A 10 nF capacitor on that pin brings the output up over a few milliseconds rather than instantly, which keeps a capacitive load from pulling the input rail down. On a board that sequences several rails, that ramp is usually the reason the capacitor value is larger than the noise requirement alone would ask for.
A six pin body in the 1.5 mm class is not easy to inspect, and the exposed pad has to be soldered for the thermal path. A board that hand assembles prototypes should verify the pad wetting before it trusts the thermal figures, because a part sitting on an unsoldered pad will run far hotter than the 250 mW dissipation suggests.
Where this order code fits
This order code fits post regulation of a switching rail in instrumentation, sensor signal chains, audio circuits and medical monitors where the noise of the switcher has to be removed before an analog stage. It also suits a quiet reference rail in a data acquisition board running from a 3.3 V or 5 V bus. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Is the output fixed? No. The TPS73401 is the adjustable member, set between 1.25 V and 6.2 V by an external divider.
What is the minimum input voltage? 2.7 V, or the output voltage plus 0.3 V, whichever is higher.
Does the noise figure need an external capacitor? Yes. The 28 uV figure assumes the noise reduction capacitor is fitted on the NR pin.
SUPERB quotes this order code with packing and date codes, and the Component Lead Time Solutions page sets out what a quiet analog rail needs when the original part becomes hard to find.