Contact Us

TPS73030DBVR

Brand: Texas Instruments
Texas Instruments TPS73030DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS73030DBVR — Power Management & Signal Chain | Superb Automation

TPS73030DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS73030DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS73030DBVR 3.0 V fixed regulator from the 200 mA TPS730 family

The TPS73030DBVR is the 3.0 V fixed member of the TPS730 line, a 200 mA low dropout regulator that runs from 2.7 V to 5.5 V and is built for rails that feed analog and radio front end loads rather than digital cores. The family is old silicon that Texas Instruments still revises, the current document being SBVS054K of June 2025, and it now exists in two chip generations under one part number. That detail matters more than the headline current, because the two generations differ in quiescent current, noise and current limit while sharing the same five pin SOT-23 body and the same order code.

The reason to pick this part instead of a cheaper 200 mA regulator is the rejection curve. It holds 68 dB at 100 Hz at full load on the legacy chip and 65 dB on the current chip, and it stays above 40 dB into the tens of kilohertz, which is the band where a switching pre-regulator puts its ripple. Output noise is 55 microvolts RMS on the legacy chip and 69 microvolts RMS on the current one, and the part is stable with a 2.2 microfarad ceramic output capacitor, so a small case size still works.

Key parameters from the SBVS054K document

Input range2.7 V to 5.5 V, absolute maximum 6 V on the legacy chip and 6.5 V on the current one
Output3.0 V fixed, adjustable member covers 1.22 V to 5.5 V through a 1.225 V reference
Current200 mA continuous, internally limited
Accuracy2 percent over load, line and temperature at the factory trimmed output
Dropout120 mV typical, 210 mV maximum at 200 mA
Quiescent current170 microamp typical and 220 microamp maximum on the legacy chip, 250 and 1000 microamp on the current chip
Shutdown current0.07 microamp typical and 1 microamp maximum on the legacy chip, 0.01 and 1 microamp on the current chip
Rejection68 dB at 100 Hz at 200 mA on the legacy chip, 65 dB on the current chip
Noise55 microvolt RMS legacy chip, 69 microvolt RMS current chip
Output capacitorStable with 2.2 microfarad ceramic, 4.7 microfarad minimum if the feed forward capacitor is omitted
PackageDBV five pin SOT-23, 2.9 mm by 2.8 mm, marking PGYI
Order codeTPS73030DBVR, 3000 pieces on a large reel, active in the addendum dated 11 April 2026

Two chips, one order code

The current document splits the electrical table into rows marked legacy chip and new chip. The legacy chip has a noise reduction pin at position four, 170 microamp of ground current and a 70 dB rejection figure at 10 mA. The current chip has a no connect at that position instead, 250 microamp of ground current, a higher current limit floor of 320 mA against 285 mA, and a different maximum input rating. Nothing on the reel label separates them, and the order code does not change, so a buyer comparing a sample from one lot against a production lot can find the ground current a third higher than the bench measurement suggested.

For a 3.0 V rail that draws a few tens of milliamps the difference is small. For a rail that sits at its 200 mA limit the difference is thermal, not electrical, because 250 microamp against 170 microamp does not change the dissipation but the 1000 microamp maximum on the new chip has to be carried in the quiescent budget of a battery product. The rule we apply at receipt is to measure ground current at the actual load rather than trust the typical column.

Where this part fits

Set top boxes, portable medical instruments, printers and building automation controllers all use a 3.0 V analog rail derived from a 5 V bus, and all of them care about rejection at low frequency because the 5 V bus is usually a switching supply. Television and monitor boards use this family in the same way for tuner and audio rails. The cross reference notes we keep for the family sit under power management cross reference, and the receipt tests that catch a chip generation change are described in incoming inspection plan.

What to check before a purchase order

Check the thermal budget first. Dropping 5 V to 3.0 V at 200 mA burns 0.4 W in a five pin SOT-23 whose junction to ambient resistance is about 182 degrees per watt on a JEDEC board, which is a 73 degree rise before the ambient is added. At 40 degrees inside an enclosure the junction sits near 113 degrees against a 125 degree limit, so the full 200 mA is not a continuous operating point at that input. Either the input is a 3.6 V rail, or the load is closer to 100 mA, or the part needs copper.

Check the addendum row before ordering. The plain TPS73030DBVR row prints Call TI in the lead finish and moisture level columns, while the .A and G4 rows of the same string print tin plating at moisture level 1 with unlimited floor life. A line that needs a documented floor life should ask for the .A or G4 row rather than assume the plain row carries the same data.

Questions that come up on this part

Can the enable pin be tied to the input? Yes, the document states the pin can be connected to IN when the shutdown function is not used, and the pin draws no current in that state. Leaving it floating is not in the specification.

Is a feed forward capacitor needed? Only for the adjustable member, where omitting it drops the output capacitor minimum to 4.7 microfarad. The fixed 3.0 V member has no feedback pin in the five pin body, so there is nothing to bypass.