Contact Us

TPS73025DBVR

Brand: Texas Instruments
Texas Instruments TPS73025DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS73025DBVR — Power Management & Signal Chain | Superb Automation

TPS73025DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS73025DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS73025DBVR 2.5 V RF regulator with 68 dB rejection

The TPS73025DBVR is the 2.5 V member of the TPS730 family, a 200 mA low dropout regulator built for RF and analogue rails. It rejects 68 dB at 100 Hz, holds 120 mV of dropout at 200 mA, and is stable with a 2.2 microfarad ceramic output capacitor. The output noise is quoted in two figures because the family spans two silicon generations: 55 microvolts RMS on the legacy chip and 69 microvolts RMS on the current one, and the document tells the reader to establish which chip is on the board before quoting a noise number.

The 2.5 V row is a common rail for RF front ends and for analogue sections that run from a 3.3 V bus, and the rejection at low frequency is what keeps the switching ripple of an upstream converter out of a phase locked loop. The family also covers 1.8 V, 3.0 V and 3.3 V fixed outputs plus an adjustable member from 1.22 V to 5.5 V.

The body is the DBV, a five pin SOT-23 of 2.9 mm by 2.8 mm. The family also ships in a five ball DSBGA of 1.35 mm by 1 mm, which is the smallest option and the one to use when the rail has to sit next to the load.

Key parameters from the SBVS054K document

Output2.5 V fixed on this order code, rows from 1.8 V to 3.3 V, adjustable 1.22 V to 5.5 V
Output current200 mA
Dropout120 mV typical at 200 mA
PSRR68 dB at 100 Hz
Noise55 microvolts RMS on the legacy chip, 69 microvolts RMS on the current chip
Output capacitor2.2 microfarad ceramic, stable across the range
EnableEnable pin, part is off when the pin is low
TransientDocument quotes line and load transient response rather than a single deviation figure
PackageDBV five pin SOT-23, 2.9 mm by 2.8 mm, also a five ball DSBGA
Order codeTPS73025DBVR, large reel, active in the vendor addendum

Two silicon generations in one part number

The document keeps the legacy and current chips on one part number and separates them in the noise table, which is honest and inconvenient. The two chips differ in noise, and the vendor's own comparison points a reader towards the TPS7A20 for new work. For a buyer the practical consequence is that a rail measured on one build can show a different noise floor on the next build even though the order code has not changed, and the difference is a few microvolts RMS rather than an order of magnitude.

The rejection figure is common to both chips, so a board that relies on the 68 dB at 100 Hz is not affected by which chip arrives. A board that relies on the noise figure should either specify the chip or accept the spread.

Where this part fits

RF front ends, phase locked loops, voltage controlled oscillators, audio sections and analogue instrumentation running from a 3.3 V bus. The 2.5 V rail gives an analogue block its own supply with 800 mV of headroom, and the rejection at low frequency is what keeps a converter's ripple out of the tuning line. Notes on post regulation after a converter are under power management cross reference, and the checks for a part with two chip generations are in incoming inspection plan.

What to check before a purchase order

Check the noise requirement against the spread. If the load needs the 55 microvolt figure, the order code alone does not guarantee it, and the safer route is a part whose noise is specified for a single chip. If the load tolerates 69 microvolts, the part is fine as it stands.

Check the dropout against the bus. At 200 mA the part needs 120 mV, so a 3.3 V bus holds a 2.5 V rail with a wide margin, and even a 2.7 V bus at minus 5 percent has enough headroom at light load. That is what makes the row comfortable on a 3.3 V board.

Check the output capacitor value and its ESR window. The family is stable with 2.2 microfarad of ceramic, and a larger electrolytic with a different ESR changes the loop. A rail that oscillates at a few hundred kilohertz after a capacitor substitution is usually this, not the regulator.

Questions that come up on this part

Is the 68 dB figure measured at full load? The rejection curve in the document covers the load range, and the number quoted in the features is the low frequency value at the test condition of the curve.

Does the enable pin need a pull up? The part is off when the pin is low, so a board that wants the rail on at power up needs the pin driven or pulled up, and a floating pin is not a defined state.