Contact Us

TPS728100180DRVR

Brand: Texas Instruments
Texas Instruments TPS728100180DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS728100180DRVR — Power Management & Signal Chain | Superb Automation

TPS728100180DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS728100180DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS728100180DRVR regulator with a pin selected 1.0 V or 1.8 V output

The TPS728100180DRVR is a 200 mA low dropout regulator whose output can be switched between 1.00 V and 1.80 V with the VSET pin. The two levels are set at the factory by EEPROM programming, and the family covers pairs across 0.9 V to 3.6 V. The purpose is a rail that has to change level at run time: a memory card that needs 1.8 V for its interface and 1.0 V in a low power state, or a processor whose core is reduced when the load falls.

Dropout is 230 mV at 200 mA, quiescent current is 50 microamps in active mode, and the accuracy is 3 percent over load, line and temperature. The document describes the part as aimed at fuse programming, memory cards and nanometric processes, which is a fair summary of the applications where a rail changes level rather than staying fixed.

The body is the DRV, a six pin WSON of 2 mm by 2 mm. One pin is the level select, so the board has to drive it from a GPIO or from a supply supervisor rather than tying it to a rail.

Key parameters from the SBVS095 document

Output levels1.00 V and 1.80 V on this order code, selected by the VSET pin
Output current200 mA
Dropout230 mV typical at 200 mA
Quiescent current50 microamps in active mode
Accuracy3 percent over load, line and temperature
Voltage optionsFactory EEPROM pairs from 0.9 V to 3.6 V
Level selectVSET pin, one of the two factory levels
PackageDRV six pin WSON, 2 mm by 2 mm
Order codeTPS728100180DRVR, large reel, active in the vendor addendum

What a two level rail means for the rest of the board

A rail that changes level is a rail that every load on it has to tolerate at both levels. A device specified for 1.8 V plus or minus 5 percent is out of specification at 1.0 V, so the level change belongs on a rail that feeds only the device that asked for it. In practice that means a dedicated regulator per level changing load, which is why this part is a single output rather than a dual.

The switching itself is a step in the output, and the load sees the transition as a transient. A device that is running during the change sees the rail pass through every voltage between the two levels, which is fine for a memory interface that is idle and not fine for an oscillator. The current a load draws during the transition is also the current the regulator has to hold while its reference moves, so a rail loaded at its limit should be brought down before the level changes. The usual sequence is to stop the load, change the level, then restart it, and the timing of that sequence belongs in the control software rather than in the regulator.

Where this part fits

Memory card interfaces, eMMC and SD rails that switch between 1.8 V and 3.3 V or 1.0 V and 1.8 V, fuse programming supplies, and low power processors with a reduced core voltage in sleep. The 200 mA rating fits a card interface rather than a core. Notes on parts that change level at run time are under power management cross reference, and the checks for a factory programmed part are in incoming inspection plan.

What to check before a purchase order

Check that the two levels on the order code are the two levels the product needs. The pair is programmed at the factory and cannot be changed on the board, so a product that later needs 1.2 V instead of 1.0 V needs a new order code rather than a resistor change. The digits in the part number encode the pair, and the addendum row is the confirmation.

Check the VSET pin drive. The pin has to be at a defined level at all times, and during power up the level it sees decides which rail the load starts on. A board that leaves the pin to a pull up resistor will start on one level and stay there until the controller acts, which may be later than the load expects.

Check the dissipation at the higher level. From a 3.3 V input into 1.8 V at 200 mA the part burns 300 mW, which the 2 mm body will carry with the pad soldered to copper. From 5 V the same load is 640 mW, which is beyond the body without a larger copper area.

Questions that come up on this part

Can the level be changed while the load is running? The regulator will follow the pin, but the load sees the transition, so the safe sequence is to idle the load first.

Is there an adjustable version? The family is factory programmed, so an adjustable rail needs a different part number.