Contact Us

TPS72733YFFR

Brand: Texas Instruments
Texas Instruments TPS72733YFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS72733YFFR — Power Management & Signal Chain | Superb Automation

TPS72733YFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS72733YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS72733YFFR 3.3 V regulator in a four ball chip scale body

The TPS72733YFFR is the same 3.3 V, 250 mA regulator as the DSE version, in the YFF four ball wafer level chip scale package of 1.2 mm by 0.8 mm on a 0.4 mm pitch. Four balls carry input, output, ground and enable, so the part has no room for a noise bypass pin and no room for a second ground, which is what the small size costs. Electrically it is the TPS727 family: 7.9 microamps of quiescent current, 163 mV of dropout at 250 mA, 70 dB of rejection at 1 kHz and a 50 mV transient for a 200 mA step.

The body is the reason to pick this order code. On a module the size of a coin, or on a sensor flex with a folded rigid section, 1.2 mm by 0.8 mm is the difference between fitting and not fitting. The part is also easier to place close to the load, which is what the transient figures assume, so the small body can produce better measured performance than the larger one on the same board.

The trade is inspection. Four balls on a 0.4 mm pitch cannot be probed with a hand tool, and the only practical check after reflow is an X-ray or a functional test on the assembled module. That is acceptable on a high volume line and awkward on a prototype bench.

Key parameters from the SBVS128F document

Output3.3 V fixed on this order code
Output current250 mA
Dropout163 mV at 250 mA, 65 mV at 100 mA
Quiescent current7.9 microamps
Load transient50 mV for a 200 mA step
PSRR70 dB at 1 kHz
Accuracy2 percent over load, line and temperature
Output capacitor1 microfarad ceramic
PackageYFF four ball WCSP, 1.2 mm by 0.8 mm, 0.4 mm pitch
Order codeTPS72733YFFR, large reel, active in the vendor addendum

What changes when the package is this small

The electrical table does not change, but three practical things do. The first is the ground connection: a single ball carries the whole return current including the transient, so the board needs a short, wide connection to the ground plane rather than a trace. The second is the thermal path: with no pad, the four balls are the only route, so the copper around them is the heat sink. The third is the enable ball, which has no room for an external pull up inside the package, so the state has to be defined on the board.

The four ball body also has no separate sense connection, so the output is regulated at the ball and the drop along the trace to the load is not corrected by the loop. The absence of a noise bypass pin means the output noise cannot be reduced below the family figure by adding a capacitor to a reference pin. A board that needs lower noise has to filter the output externally or use a different part with a bypass pin.

Where this part fits

Wearables, sensor modules, camera modules, hearing instruments, medical patches and any product where the board area is the dominant constraint. The 250 mA rating covers a radio burst or a small motor, and the low quiescent current keeps the rail alive between events. Notes on the family rows and their equivalents in other bodies are under power management cross reference, and the handling rules for a wafer level part are in incoming inspection plan.

What to check before a purchase order

Check that the assembly line can place and reflow a 0.4 mm pitch wafer level part. A line qualified on 0.5 mm pitch and 0402 passives may need a new stencil and a new placement recipe, and a part this small is unforgiving of a placement offset. The reflow profile also matters, because the ball collapse is what forms the joint and there is no lead to compensate for a cold joint.

Check the ground and output routing against the current. The 250 mA rating assumes the balls are connected to planes, not to traces, and a two layer board with a single via per ball will show a higher dropout than the document figure.

Check the moisture level before reflow. The addendum gives level 1 for this body, which means no bake is required, but a reel that has been stored open in a humid room is still worth a check before a build.

Questions that come up on this part

Is this the same die as the DSE version? The family document covers both bodies, and the electrical table is shared.

Can it be used without a ground plane? It can be assembled, but the transient and thermal figures assume one, so a board without a plane should be measured rather than assumed.