TPS72733DSER
Product Specifications
TPS72733DSER
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS72733DSER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS72733DSER 3.3 V 250 mA regulator with 7.9 microamp quiescent current
The TPS72733DSER is the 3.3 V member of the TPS727 family, a 250 mA low dropout regulator with 7.9 microamps of quiescent current and a fast transient response. Dropout is 65 mV at 100 mA, 130 mV at 200 mA and 163 mV at 250 mA, and the output is set at the factory by EEPROM programming across a range from 0.9 V to 5 V, with 2 percent accuracy over load, line and temperature. Rejection is 70 dB at 1 kHz, and the part is stable with a 1 microfarad ceramic output capacitor.
The load transient figure is the one that separates this family from a general purpose low quiescent regulator: 50 mV of deviation for a 200 mA load step in either direction. That matters on a radio rail, where the current jumps between a few microamps in receive and hundreds of milliamps in transmit, and where a slow loop would let the rail sag far enough to reset the baseband.
The body on this order code is the DSE, a six pin WSON of 1.5 mm by 1.5 mm. The same die is also offered in the YFF four ball WCSP, which is the smallest option in the family.
Key parameters from the SBVS128F document
| Input range | 2.5 V to 5.5 V class supply, with the output set by factory EEPROM |
| Output | 3.3 V fixed on this order code, rows from 0.9 V to 5 V |
| Output current | 250 mA |
| Dropout | 65 mV at 100 mA, 130 mV at 200 mA, 163 mV at 250 mA |
| Quiescent current | 7.9 microamps |
| Load transient | 50 mV for a 200 mA load or unload step |
| PSRR | 70 dB at 1 kHz |
| Accuracy | 2 percent over load, line and temperature |
| Output capacitor | 1 microfarad ceramic, stable across the range |
| Package | DSE six pin WSON, 1.5 mm by 1.5 mm |
| Order code | TPS72733DSER, large reel, active in the vendor addendum |
How the fast loop is paid for
A 7.9 microamp quiescent current with a 50 mV transient for a 200 mA step is a combination that needs a loop which turns on quickly. The family achieves it with a comparator path that reacts before the main error amplifier has settled, and the cost is a small increase in supply current during the transient rather than in steady state. For a radio rail that is the right trade: the average current stays low, and the peak capability is there when the transmitter keys.
The other cost is the output capacitor requirement. A 1 microfarad ceramic is the minimum the part is specified with, and the transient figure assumes it sits at the pin. A board that puts the capacitor at the load, or uses a 100 nanofarad part because the rail looked quiet on the bench, will see a larger deviation than the document promises.
Where this part fits
Wireless handsets, smart phones, PDAs, MP3 players, wireless LAN, Bluetooth and Zigbee modules, remote controls and portable consumer products. The 3.3 V row is the one that feeds a radio front end or a sensor hub directly from a lithium cell, and the 250 mA rating covers a transmitter burst on a small module. Notes on choosing between the fixed rows of this family are under power management cross reference, and the checks for an EEPROM trimmed part are in incoming inspection plan.
What to check before a purchase order
Check the exact output row. The family is factory programmed across 0.9 V to 5 V, so two order codes that differ in one digit can put 3.0 V or 3.6 V on a rail that expects 3.3 V, and the part will work well enough on a bench to pass a functional test. The voltage is in the order code, and the addendum row is the confirmation.
Check the input headroom at the lowest battery voltage. At 3.3 V out and 250 mA the part needs about 163 mV, so the input has to stay above 3.46 V for full regulation, which a lithium cell only does for part of its discharge. A rail that must hold 3.3 V to the end of the cell needs a buck-boost, not a linear regulator.
Check the thermal path in the 1.5 mm body. The dissipation at 250 mA and a 0.5 V difference is 125 mW, which is manageable, but a 5 V input into 3.3 V at the same current is 425 mW and needs the pad soldered to copper that the vendor's table assumes.
Questions that come up on this part
Is the 50 mV transient a guaranteed limit? It is the vendor's measured response for the stated step, and a faster edge or a larger step produces a larger deviation.
Can the output be trimmed on the board? No. The voltage is set in EEPROM at the factory, so a rail that needs adjustment in production belongs on an adjustable part.