Contact Us

TPS72615DCQR

Brand: Texas Instruments
Texas Instruments TPS72615DCQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS72615DCQR — Power Management & Signal Chain | Superb Automation

TPS72615DCQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS72615DCQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS72615DCQR 1 A regulator with a built in supervisor

The TPS72615DCQR is a 1.5 V, 1 A low dropout regulator with a supply voltage supervisor inside the same body. It runs from 1.8 V to 6 V, holds 170 mV of dropout at the full amp, and draws 210 microamps of ground current at full load. The supervisor watches the output and drives an active low RESET when the rail falls out of regulation, with a 200 ms delay before releasing it, which is most of the reset chain a processor board needs and the reason the part exists in this shape.

The body is the DCQ, a six pin SOT-223 with a tab. That package is what makes a 1 A linear regulator practical: the tab is the thermal path, and at 1 A the dissipation is the parameter that decides whether the part can be used at all. The family covers 1.26 V, 1.5 V, 1.6 V, 1.8 V and 2.5 V, so a board with a core rail and a DDR rail can be built from one document.

Putting the supervisor in the regulator removes three parts from a bill of materials: the reset IC, its timing capacitor and the divider that sets the threshold. What it does not remove is the need to check the threshold against the processor's own minimum supply, because the supervisor trips on the regulator output, not on the voltage the processor actually sees at its pins.

Key parameters from the SLVS403H document

Input range1.8 V to 6 V
Output1.5 V fixed on this order code, with 1.26 V, 1.6 V, 1.8 V and 2.5 V siblings
Output current1 A
Dropout170 mV at 1 A
Ground current210 microamps at full load
SupervisorActive low RESET, released 200 ms after the output is in regulation
Reset behaviourAsserts when the output falls out of regulation, holds through the delay
PackageDCQ six pin SOT-223 with a thermal tab
Order codeTPS72615DCQR, 2500 pieces on a large reel, active in the vendor addendum

What the integrated supervisor changes on a board

A supervisor that sits inside the regulator sees the rail at the regulator output, which is the cleanest point on the rail and the least useful one. The processor sees the rail after the copper, and a board with a long trace or a narrow pour has a drop between the two that grows with load. A threshold that is correct at the regulator can therefore release reset while the processor is still below its minimum, and the failure appears as an occasional bad boot rather than as a rail that is obviously low.

The 200 ms delay is the other number to check. A processor whose data sheet asks for a longer period after the rail is valid needs the delay extended externally or a different supervisor, and a processor that needs a shorter one will boot later than its own timing allows, which is usually harmless but costs start-up time on a product that is power cycled often.

Where this part fits

Processor and DSP boards, FPGA core rails, industrial controllers and instrument front ends that need a 1 A rail with a clean reset. The 1.5 V row is common on older cores and on DDR termination, where the load is a heavy DC current with modest transient content. Notes on replacing a discrete regulator plus supervisor pair sit under power management cross reference, and the thermal checks that decide whether a 1 A linear part is viable are in incoming inspection plan.

What to check before a purchase order

Check the dissipation before anything else. At 1 A from a 3.3 V input into a 1.5 V output the part burns 1.8 W, which the SOT-223 tab can carry only with a copper area the vendor's thermal table assumes. From a 2.5 V input the same load is 1.0 W, which is a different proposition, and that is why the part usually follows a converter rather than sitting on the main bus.

Check the thermal tab solder joint. The tab is the only path with a low enough resistance to hold 1.8 W, and a joint with voids raises the junction temperature by tens of degrees. On a board that is reflowed with a stencil cut for a smaller pad the tab can end up partially wetted, which is a defect that passes a continuity test and fails in a hot enclosure.

Check the reset polarity against the processor. The output is active low, so a processor whose reset is active high needs an inversion, and a board that assumes the other polarity will hold the processor in reset instead of releasing it.

Questions that come up on this part

Does the supervisor have its own threshold trim? No, the threshold follows the regulator output, so the accuracy of the trip point is the accuracy of the regulator plus the supervisor offset.

Can the delay be shortened? Only externally. The 200 ms figure is internal, and a shorter delay needs a different supervisor or a processor that tolerates it.