Contact Us

TPS72018DRVR

Brand: Texas Instruments
Texas Instruments TPS72018DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS72018DRVR — Power Management & Signal Chain | Superb Automation

TPS72018DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS72018DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS72018DRVR: 350 mA low dropout regulator with a bias pin, fixed 1.8 V output, in a 2 mm by 2 mm WSON

TPS72018DRVR is a linear regulator that turns a 3.3 V or 2.5 V rail into a quiet 1.8 V rail with 110 mV of dropout and 48 uV of noise in a WSON body of 6 pins. It is the 1.8 V member of the family and the one most often used as a post regulator, because a 1.8 V load on a 3.3 V board usually has more headroom than it needs and the question becomes dissipation rather than dropout.

Order code and package

Order codeTPS72018DRVR, DRV package, WSON 2 mm by 2 mm, six pins with a thermal pad, 3000 pieces on a large reel
Body optionsDRV six pin WSON over the full range, YZU five pin die scale package over a narrower one
Fixed output1.8 V on this code, with TPS72010 at 1.0 V, TPS72012 at 1.2 V and the TPS7201 adjustable
Output capacitor2.2 uF ceramic, the value the transient and start-up limits are measured at
PinsIN, OUT, BIAS, EN, GND and the thermal pad
TrimThe output is set at wafer level, so there is no divider and no external component in the accuracy budget

Electrical parameters that decide the application

Input range1.1 V to 4.5 V on IN, with the output at least 500 mV below the input for the published accuracy
Bias rail2.5 V to 5.5 V on BIAS, which can be the same 3.3 V rail that feeds IN
Output current350 mA continuous, current limited and thermally protected
Dropout110 mV at 350 mA, so 1.91 V is the minimum input at full load and a 2.5 V rail has 590 mV to spare
Quiescent current38 uA typical on the bias rail
Noise48 uV RMS from 10 Hz to 100 kHz, 0.2 per cent of the output
Rejection80 dB from IN and 70 dB from BIAS from 10 Hz to 10 kHz
Accuracy1 per cent over line, load and temperature on the DRV package
Transients15 mV for a 0 to 350 mA step in 1 us, 2 mV for a 600 mV step on the bias rail
Start-up140 us, monotonic, 3 per cent overshoot, inrush limited to 100 mA plus the load

Family variants and how they differ

TPS72012DRVRthe 1.2 V trim of the same die, for a core rail rather than a peripheral rail
TPS72010DRVRthe 1.0 V trim, which needs the tightest headroom of the three
TPS7201DRVRthe adjustable member, for a rail that is set by a divider instead of by the order code
TPS7A20a lower current alternative for a 1.8 V rail that only carries tens of milliamps
A buck converterthe right answer when the 1.5 V of headroom would turn into more than a watt of heat

Points to check before this part goes on a BOM

At 1.8 V out from a 3.3 V rail, the regulator drops 1.5 V and the question is no longer dropout but heat. At the full 350 mA that is 525 mW in a 2 mm by 2 mm WSON, which needs a copper pad and thermal vias under the part. The same rail at 100 mA is 150 mW and needs nothing special, so the load current decides whether this part is the right choice at all.

From a 2.5 V rail the drop is 700 mV and the dissipation at 350 mA falls to 245 mW, which the body handles without a plane. That is the configuration the part was built around, and a board that has a 2.5 V rail available should feed this regulator from it rather than from 3.3 V, purely on thermal grounds.

The bias pin can be tied to the same 3.3 V rail as the input on this voltage, which removes the sequencing problem that the 1.0 V and 1.2 V versions have. It cannot be tied to the 1.8 V output, because 1.8 V is below the 2.5 V floor, and it cannot come from a rail that rises after the enable signal without holding the output at zero.

The 48 uV of noise and the 80 dB of rejection are the reason to put this part after a converter rather than trusting the converter's own ripple. On a 1.8 V rail a 12 bit converter has a 440 uV step, so the regulator's own noise is a ninth of a step and the switching products of the converter in front of it are what the loop and the output capacitor have to remove. Rejection is specified only to 10 kHz, so the 2.4 MHz content is filtered by capacitance, not by the amplifier.

The 1 per cent accuracy covers line, load and temperature on the DRV body, which on 1.8 V is 18 mV. That is smaller than the tolerance of most loads' own specification, and it is why a rail like this can feed an analog front end without a trim step in production. The YZU body carries a narrower temperature range for the same figure, so a form factor change is also a specification change.

The 15 mV load transient for a 0 to 350 mA step in 1 us is the part's response with a 2.2 uF ceramic output. Increasing the capacitor reduces the deviation but the loop is specified against that value, and a board that fits 10 uF to be safe should check the stability rather than assume more capacitance is better. The start-up inrush rises with the capacitor as well, and the 100 mA limit is quoted at 2.2 uF.

The start-up is 140 us and monotonic, so a rail that has to come up after a converter is stable can be sequenced with the enable pin and nothing else. There is no soft-start capacitor to size, which removes a component and a variable, and the inrush limit protects the rail in front of it. The overshoot limit of 3 per cent is small enough that a load with a 1.8 V plus or minus 5 per cent window never sees it.

The dropout of 110 mV is what allows the part to keep regulating when the input sags. On a 2.5 V rail with five per cent tolerance the low end is 2.375 V, which is 465 mV above the 1.91 V floor, so a load step that pulls the rail down by 300 mV still leaves the regulator in regulation. On a 1.91 V input there is no margin at all, and the output follows the input down with the pass element fully on.

Where this order code fits

It belongs on the 1.8 V rail of an analog front end, a codec, a sensor interface or an FPGA auxiliary supply, where the rail comes from a 2.5 V or 3.3 V bus and the load is a few hundred milliamps. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Can it run from 3.3 V at 350 mA? It regulates, but it dissipates 525 mW in a 2 mm by 2 mm body, so it needs a thermal pad and vias. From a 2.5 V rail the same load is 245 mW and needs nothing extra.

Can the bias pin share the 3.3 V input? Yes. BIAS needs 2.5 V to 5.5 V, and 3.3 V is inside that window, which removes the sequencing order that the 1.0 V and 1.2 V versions require.

Is more output capacitance better? Not automatically. The transient and start-up limits are specified at 2.2 uF, and a larger capacitor changes the loop and raises the inrush that the 100 mA limit was written for.

Is the 1.0 V version pin compatible? Yes, same body and pin out, but it is a different order code with a different output, so it is a substitution on the BOM rather than a resistor change.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.