TPS720105QDRVRQ1
Product Specifications
TPS720105QDRVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS720105QDRVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS720105QDRVRQ1 1.05 V automotive RF regulator with a bias rail
The TPS720105QDRVRQ1 is a 1.05 V, 350 mA low dropout regulator in the TPS720-Q1 family, a dual rail part that separates the power path from the control circuit. The main input, VIN, only has to sit a little above the output, and a second pin, VBIAS, powers the internal control circuit from any rail at least 1.4 V above the output. That split is what allows the regulator to hold a 1.05 V rail from a converter output that is barely above it, which is the arrangement a power sensitive board wants because the converter can then run at high efficiency without leaving headroom for a linear stage.
The part is AEC-Q100 grade 1, minus 40 to plus 125 degrees ambient, with HBM level H2 and CDM level C6. Quiescent current is 38 microamps, dropout is 110 mV at 350 mA, noise is 48 microvolts RMS over 10 Hz to 100 kHz, rejection is 80 dB from VIN and 70 dB from VBIAS over 10 Hz to 10 kHz, and the transient response is quoted as 15 mV for a 0 to 350 mA step in 1 microsecond.
One unusual feature is documented: at light load the output keeps regulating with the IN pin left floating, because the drive current is then taken from VBIAS. That is useful when the converter feeding VIN is switched off in sleep and the small load still needs its rail.
Key parameters from the SBVS278A document
| Qualification | AEC-Q100 grade 1, minus 40 to plus 125 degrees ambient |
| ESD | HBM level H2 and CDM level C6 |
| Input range | VIN 1.1 V to 4.5 V, VBIAS at least 1.4 V above the output |
| Output | 1.05 V on this order code, 0.9 V to 3.6 V across the family |
| Output current | 350 mA |
| Dropout | 110 mV at 350 mA |
| Quiescent current | 38 microamps |
| Noise | 48 microvolts RMS from 10 Hz to 100 kHz |
| Rejection | 80 dB from VIN and 70 dB from VBIAS over 10 Hz to 10 kHz |
| Start-up | 140 microseconds, soft start with the current limited to 100 mA plus the load |
| Output capacitor | 2.2 microfarad ceramic, stable across the range |
| Package and order code | DRV six pin WSON 2 mm by 2 mm, TPS720105QDRVRQ1 on a large reel |
Why the bias rail is the point of this part
A conventional low dropout regulator needs its input to sit above the output by more than the dropout voltage, and on a 1.05 V rail that means the converter feeding it has to be set higher than the rail needs. The bias pin removes that constraint: the control circuit runs from a 3.3 V or 5 V rail that is already on the board, and the power path only has to carry the load current across a small difference. A converter set to 1.2 V can then feed a 1.05 V rail with 40 mV of margin, which is where the efficiency gain comes from.
The bias current is small, on the order of the regulator's own quiescent current, so it does not put a meaningful load on the rail that supplies it. What it does require is that the bias rail is present before or with the input, because the part cannot start without it.
Where this part fits
Automotive camera and radar modules, infotainment processors, sensor fusion boards and any automotive module with a core rail just below a converter output. The grade 1 qualification and the 2 mm body make it a fit for a module that has to sit behind a connector in a hot location. Notes on putting a bias rail regulator after a converter are under power management cross reference, and the checks for a two rail part on receipt are in incoming inspection plan.
What to check before a purchase order
Check that the bias rail is at least 1.4 V above the output at the lowest point of its tolerance. A 2.5 V bias rail against a 1.05 V output leaves 1.45 V, which is inside the requirement at nominal and outside it if the rail sags by 5 percent. The requirement is a floor, not a target.
Check the input capacitor and the converter loop together. The regulator's rejection figures are quoted with a low impedance source, and a converter that is barely above the output has a large output impedance near its crossover, so the two loops can interact. The usual fix is a small ceramic at the regulator input and enough converter output capacitance to keep the impedance low at the regulator's bandwidth.
Check the light load behaviour against the sleep state of the product. The feature that lets the output regulate with IN floating is useful, but it has to be confirmed at the actual sleep current, because the bias path has a finite current capability.
Questions that come up on this part
Can VIN and VBIAS be tied together? Yes, at the cost of the dropout advantage, since the part then behaves like a single rail regulator and the bias current comes from the same source.
Is the 15 mV transient figure a guaranteed limit? It is the vendor's measured response to a 0 to 350 mA step in 1 microsecond, and a real load with a faster edge will produce a larger deviation.