Contact Us

TPS71918-28DRVR

Brand: Texas Instruments
Texas Instruments TPS71918-28DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS71918-28DRVR — Power Management & Signal Chain | Superb Automation

TPS71918-28DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS71918-28DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS71918-28DRVR dual 1.8 V and 2.8 V regulator

The TPS71918-28DRVR is a dual low dropout regulator in one six pin WSON body, with one output at 1.8 V and the other at 2.8 V, both rated at 200 mA. It is the TPS719 member of the family, which means it carries an active pulldown on each output: when an enable goes low, the output is pulled down through an internal device instead of being left to decay through the load. On a board with two rails that have to come down in a defined order, that behaviour is what keeps one rail from back feeding the other through a protection diode.

Total quiescent current with both regulators enabled is 90 microamps, which is the number that matters on a battery product with two always-on rails, because a second regulator does not double the budget. Dropout is 230 mV at 200 mA, rejection is 65 dB at 1 kHz and 45 dB at 1 MHz, and the accuracy is 3 percent over load, line, process and temperature.

The output pair is set at the factory by EEPROM programming, and the family covers combinations from 0.9 V to 3.6 V. The pair on this order code, 1.8 V and 2.8 V, is a common arrangement for a processor core plus a sensor or radio rail.

Key parameters from the SBVS088C document

Outputs1.8 V and 2.8 V, each 200 mA
Input range2.7 V to 6.5 V
Dropout230 mV typical at 200 mA on each output
Quiescent current90 microamps typical with both regulators enabled
PSRR65 dB at 1 kHz and 45 dB at 1 MHz
Accuracy3 percent over load, line, process and temperature
PulldownActive output pulldown on the TPS719 member when an enable is low
Output capacitorsStable with 1 microfarad ceramic parts on each output
Voltage optionsFactory EEPROM combinations from 0.9 V to 3.6 V
PackageDRV six pin WSON, active in the vendor addendum
Order codeTPS71918-28DRVR, large reel

What the active pulldown is for

An active pulldown matters in three situations. The first is a rail that feeds a device with a large input capacitor, where a passive discharge through the load takes long enough that the next power up begins with a charged capacitor and the inrush protection is defeated. The second is a rail that can be back fed from an interface that stays powered, such as a USB port, where the pulldown holds the rail down and stops the regulator from being reverse biased. The third is a strict power down order, where a rail that decays slowly keeps a device half alive while the rest of the board is already off.

The cost of the pulldown is a small current when the regulator is disabled. On a product that is off for long periods, that current has to be counted against the 90 microamp operating figure, because the disabled state is the state the product spends most of its life in.

Where this part fits

Battery products with a processor and a radio, handheld instruments, portable medical devices, and any board that has to replace two single regulators with one body to save area. The two outputs on a six pin body also simplify the sequencing, since one enable pin controls each output and the pulldown makes the off order deterministic. Our notes on consolidating two rails into one package are under power management cross reference, and the checks for a dual regulator on receipt are in incoming inspection plan.

What to check before a purchase order

Check the pair against the load requirements, because the suffix is the only place the voltages appear and a similar looking order code can carry a different pair. The family covers combinations from 0.9 V to 3.6 V, and two parts that differ by one digit can put 3.0 V on a rail that expects 2.8 V.

Check the total dissipation in one body. Both regulators share a package, so a 5 V input with 200 mA on each output burns 1.08 W in a six pin WSON, which needs the thermal pad soldered to a copper area rather than to a thin trace. The 200 mA rating on each output assumes the other output is not also at full load in a hot ambient.

Check the enable behaviour at power down. If one rail feeds a device that drives a pin on a device on the other rail, the pulldown is what keeps the interface from being back powered during shutdown, and the order of the two enables becomes a board level decision rather than a detail.

Questions that come up on this part

Are the two outputs independently enabled? Yes, each output has its own enable pin, which is what allows the rails to be sequenced.

Can the pulldown be disabled? No, it is part of the TPS719 member. The TPS718 member of the same family is the version without it, in the same pinout.