TPS715345DCKR
Product Specifications
TPS715345DCKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS715345DCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS715345DCKR: a 50 mA wide input regulator with a 3.45 V fixed output and 3.2 uA of quiescent current
TPS715345DCKR is a linear regulator that holds a fixed 3.45 V output from an input anywhere between 2.5 V and 24 V while drawing microamps of ground current at any load from zero to full in a SC70 body of 5 pins. The DCK body is the five pin SC70 at 2.00 mm by 1.25 mm, and the part exists for one reason, a rail that has to survive a 24 V transient and still draw almost nothing when the load is asleep.
Order code and package
| Catalogue string | TPS715345DCKR, where the three digit code 345 decodes as a 3.45 V nominal output in the vendor nomenclature |
| Body | SC70, five pins, DCK, 2.00 mm by 1.25 mm |
| Reel | 3000 pieces on a large tape and reel on every one of the four published rows |
| Finish and moisture | NIPDAU plating on the .A rows, moisture level 1, 260 C, unlimited floor life |
| Temperature | minus 40 to 125 C junction, which is the operating range rather than a storage range |
| Marking | BNY |
| Document | SLVS338T, revised December 2022 |
| Reel check | TPS715345DCKR, the .A row, the G4 row and the M3 row all print 3000 pieces, so the packing is the same across the family variants and only the silicon revision changes |
Electrical parameters that decide the application
| Input range | 2.5 V to 24 V for the legacy chip and up to 30 V maximum on the new chip, which is a real difference between two parts that share a part number |
| Output | 3.45 V fixed on this code, with the adjustable member of the same family spanning 1.205 V to 15 V from an external divider |
| Output current | 50 mA maximum, and the whole specification is written at that current rather than at a fraction of it |
| Quiescent current | 3.2 uA typical, 4.2 uA maximum on the legacy chip and 4.8 uA maximum on the new chip, and the figure holds across the full load range rather than only at no load |
| Accuracy | plus or minus 4 per cent over line, load and temperature, which is looser than a precision reference and normal for a part of this class |
| Dropout | 415 mV typical at 50 mA on both chips, with a 750 mV maximum on the legacy chip and a 525 mV maximum on the new one |
| Noise | 575 uV RMS on the legacy chip and 425 uV RMS on the new chip, both over 200 Hz to 100 kHz with a 10 uF output capacitor at 50 mA |
| Ripple rejection | 60 dB at 100 kHz with a 10 uF output capacitor, which is the frequency that matters when the input is a switching supply |
| Current limit | 125 mA minimum and 750 mA maximum at a shorted output, so the part survives a fault without an external fuse |
| Output capacitor | stable with 0.47 uF or more, which removes the ESR window that older regulators of this size demanded |
| Soft start | internal, which limits the inrush at turn on without an external capacitor |
| Reverse behaviour | the pass FET conducts from output to input if the output is driven above the input with the device enabled, which is worth knowing on a rail that is back fed |
| Thermal | the five pin SC70 has little copper to work with, so 24 V in and 3.45 V out at 50 mA is 1.03 W and no SC70 survives that without a thermal calculation |
Fixed codes, adjustable member and the two chips
| TPS715345DCKR | the plain row, active, 3000 pieces on a large reel |
| TPS715345DCKR.A | the revision letter row, same body and same reel, printed separately in the addendum |
| TPS715345DCKRG4 | the green material row, same body and reel |
| TPS715345DCKRM3 | the M3 silicon row, which is the new chip with the 30 V absolute maximum and the lower noise |
| TPS71501 | the adjustable member, 1.205 V to 15 V, for an output that no fixed option covers |
| TPS715A | the 80 mA relative with a larger package, for a load that outgrows 50 mA |
Points to check before this part goes on a BOM
Two silicon generations share this part number and they do not have the same input ceiling. The legacy chip stops at 24 V and the new chip is rated to 30 V absolute maximum, and the maximum dropout differs as well, 750 mV against 525 mV at 50 mA. Nothing on the reel label distinguishes them beyond the M3 suffix, so a build that leans on the 30 V margin has to name the M3 row on the order.
3.45 V is an odd rail and that is exactly why the code exists. It sits above the 3.3 V nominal of a lithium iron phosphate cell under charge and below the 3.6 V of a fully charged lithium ion cell, so a divider or a fixed regulator built for 3.3 V either drops out or over stresses the load at the top of the charge curve. Where a radio or a sensor has a 3.6 V absolute maximum, 3.45 V is the compromise that leaves 150 mV of headroom.
The 3.2 uA quiescent current is only useful if the rest of the circuit agrees. At 50 mA of load the ground current is a rounding error, and at 0 mA it is the entire consumption of the rail. That makes this part a candidate for a always on housekeeping rail where the microcontroller sleeps for months, and a poor candidate for a rail that is switched, because a switched rail does not benefit from a low no load current.
Dropout of 415 mV typical at 50 mA bounds the input. A 3.45 V output needs at least 3.87 V at the input to stay in regulation at full load, and the maximum dropout of 750 mV on the legacy chip pushes that to 4.2 V. A 5 V rail has room. A 3.7 V cell does not, and that is the calculation that decides whether this part or a lower dropout relative is the right choice.
Power dissipation is the limit nobody checks until the board runs hot. The worst case in a 24 V system is 24 V in, 3.45 V out, 50 mA, which is 20.55 V across the pass FET or 1.03 W. The SC70 junction to ambient figure is around 250 to 300 C per W without copper, so that case is not survivable at 50 mA continuous and has to be reduced to a few milliamps or moved to a part with a thermal pad.
The output capacitor is unusually forgiving at 0.47 uF. Older regulators of this shape wanted a tantalum with a specific ESR and would oscillate on a ceramic. This one is stable with a small ceramic, which is what makes the five pin body usable in a module where the capacitor has to be the same size as the regulator. Noise at 425 uV RMS is the price, and a 10 uF output capacitor plus a feed forward capacitor brings it down further.
Reading the two chip generations correctly
The revision history is the only place where the split is spelled out in one place. Revision T added the M3 rows and the new chip curves, and the electrical table now prints separate figures for the legacy chip and the new chip in the same rows: ground current, line regulation, noise, current limit and dropout all have two values. A quotation that copies one number without knowing which chip is behind it can be out by 40 per cent on dropout and by 150 uV on noise.
In practice this matters at the two ends of the range. At 24 V in the new chip has 6 V of margin to its absolute maximum and the legacy chip has none, so a surge clamp that lets 26 V through will kill one and not the other. At 50 mA and 3.45 V out the maximum dropout of 750 mV against 525 mV decides whether a 4.0 V input is inside specification, and that is a difference a customer will notice on a bench at low temperature.
What the 3.45 V option is for
A 3.45 V rail appears in products that sit between a 3.3 V logic rail and a 3.6 V absolute maximum. A radio module specified to 3.6 V absolute maximum cannot be run from a 3.7 V cell directly, and a 3.3 V regulator wastes the top of the cell and drops out at the bottom. The 3.45 V fixed option takes the middle of the cell curve, and the low dropout means it stays in regulation until the cell is nearly empty.
The catch is the tolerance. Plus or minus 4 per cent on 3.45 V is 3.31 V to 3.59 V, so the top of the window is 10 mV from the 3.6 V absolute maximum of a typical module. A product that needs margin to both ends should use the adjustable member with a 1 per cent divider, or accept that the fixed part is a 3.3 V rail in disguise at the bottom of its tolerance band. This is the sort of arithmetic worth doing before the first article is built rather than after.
Where this order code fits
This is the housekeeping rail in a meter, a building controller, a payment terminal, a grid sensor or a medical handheld, where the input can swing to 24 V and the load is asleep most of the time Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.
Questions buyers ask
Is 3.45 V the top of the tolerance or the nominal? It is the nominal. Accuracy is plus or minus 4 per cent over line, load and temperature, so the output window runs from about 3.31 V to 3.59 V and the top sits within 10 mV of a 3.6 V absolute maximum.
Can it run from a 3.7 V lithium cell at 50 mA? Only above about 4.2 V at the input on the legacy chip, because the maximum dropout is 750 mV. On the new chip the maximum is 525 mV, which brings the floor to about 3.98 V. A single cell sits below that for most of its discharge.
Which chip am I buying? The M3 suffix is the new chip. The plain, .A and G4 rows are the legacy chip, with the 24 V ceiling and the 750 mV maximum dropout. Only the marking and the order code separate them.
How low is the current at no load? 3.2 uA typical and 4.8 uA maximum on the new chip, with the same 3.2 uA typical on the legacy chip. The figure holds across the full load range, which is unusual for a regulator of this class.
What output capacitor does it need? 0.47 uF or more, and a ceramic is fine. A 10 uF part lowers the noise and improves the rejection at 100 kHz, and the data sheet quotes both figures at that capacitance.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.