Contact Us

TPS70938DBVR

Brand: Texas Instruments
Texas Instruments TPS70938DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS70938DBVR — Power Management & Signal Chain | Superb Automation

TPS70938DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS70938DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS70938DBVR 3.8 V fixed regulator for a rail above 3.3 V

The TPS70938DBVR is the 3.8 V member of the TPS709 family, a 150 mA regulator that runs from 2.7 V to 30 V with 1 microamp of quiescent current. A 3.8 V rail is unusual enough that it is worth saying why it exists: it is the supply that a lithium cell powered product uses when it wants a rail that stays above 3.3 V for the whole discharge and does not want a boost converter in the path. It is also the rail some RF front ends and some precision references ask for when a 3.3 V rail leaves too little headroom above their internal reference.

The part is 2 percent accurate over temperature, blocks reverse current, limits its own output current and shuts down on overtemperature. Shutdown current is 150 nA, which is what makes it usable as the always-on rail of a product that sleeps for months. The body on this order code is the DBV five pin SOT-23 of 2.9 mm by 1.6 mm.

The input floor of 2.7 V sits below the 3.8 V output, so a single lithium cell whose voltage has fallen to 3.0 V cannot hold this rail up; the part enters dropout and the output follows the input down. That is a normal consequence of a linear regulator and not a fault, but it changes the usable capacity of the cell, and a product that quotes a run time on a 3.8 V rail has to account for it.

Key parameters from the SBVS186H document

Input range2.7 V to 30 V
Output3.8 V fixed on this order code, 1.2 V to 6.5 V across the family
Output current150 mA rated, 200 mA peak
Quiescent current1 microamp typical
Shutdown current150 nA typical with the enable pin low
DropoutSpecified for outputs of 2.8 V and above, so this rail is inside the specified window
Accuracy2 percent over temperature
ProtectionReverse current, current limit and thermal shutdown
PackageDBV five pin SOT-23, 2.9 mm by 1.6 mm
Order codeTPS70938DBVR, large reel, active in the vendor addendum

What a 3.8 V rail does to the rest of the board

A 3.8 V rail is above the 3.3 V that most logic expects, so everything downstream either has its own regulator or is a device rated for 5 V. The usual arrangement is a 3.8 V rail for the analogue and RF section and a separate 3.3 V or 1.8 V rail for the digital side, with the 3.8 V rail providing the headroom that a low dropout regulator on the analogue side needs. Putting a 3.8 V rail directly onto a 3.3 V only device is a mistake that passes a bench test and fails after a few hundred hours.

The regulator itself dissipates the difference between input and output at the load current. On a 5 V input at 150 mA that is 0.18 W, which the SOT-23 can carry with a reasonable copper area. On a 12 V input the same load becomes 1.2 W, which no five pin SOT-23 will hold for long, so the high input side of this family belongs with small loads or with a pre regulator.

Where this part fits

Handheld instruments with an analogue front end, RF modules that want a rail above 3.3 V, battery products that need a stable rail until the cell is nearly flat, and mains powered equipment with a 12 V or 24 V internal bus and a small load. The 30 V input also makes it usable on a 24 V industrial line where the load is a few milliamps, such as a sensor bias or a reference supply. Substitution notes across the fixed voltage rows are under power management cross reference, and the bench checks for a high input rail are in incoming inspection plan.

What to check before a purchase order

Check the cell chemistry against the rail. A single lithium cell starts at 4.2 V and falls to 3.0 V, so a 3.8 V rail is in regulation for the first part of the discharge and in dropout for the rest, which means the load sees a falling rail for most of the run time. A product that needs 3.8 V until the last minute needs a buck-boost converter, not a linear regulator.

Check the thermal path at the actual input voltage, not at the nominal one. A 24 V bus with a surge to 30 V is inside the rating but pushes the dissipation up at the same load, and the package temperature is what limits the current. Also confirm the output capacitor is a ceramic part inside the stable range, since the family is compensated for a small ceramic output and a larger electrolytic changes the loop.

Questions that come up on this part

Can this hold 3.8 V from a 3.3 V rail? No. A linear regulator cannot produce an output above its input, so the rail follows the input down once the headroom is gone.

Is the 1 microamp figure the total current at no load? It is the quiescent current of the regulator with the enable pin high and no load. The load leakage adds to it, and on a 3.8 V rail a single 100 kilohm divider already draws 38 microamps.